KYA 1-1/4" × .120" galvanized coil roofing nails are smooth shank, wire-collated fasteners designed for use with compatible coil roofing nailers. The 1-1/4 inch length, .120 inch shank diameter, full round wide head and diamond point make this configuration suitable for professional roofing applications including asphalt shingles, roofing underlayment and insulation board fastening where this nail specification is required.
Product code KYA-3.05X32 uses 15-degree wire coil collation and an electro-galvanized finish. The nails are packed at 7,200 pieces per carton for contractors, roofing fastener distributors, wholesalers and other professional buyers.
| Product Type | Wire Coil Roofing Nail |
| Model | 1-1/4" × .120" |
| Product Code | KYA-3.05X32 |
| Length | 1-1/4" (32mm) |
| Shank Diameter | 0.120" (approximately 3.05mm) |
| Shank Type | Smooth Shank |
| Head Type | Full Round Wide Head |
| Point Type | Diamond Point |
| Collation | Wire Coil |
| Collation Angle | 15° |
| Material | Steel |
| Finish | Electro-Galvanized |
| Packing | 7,200 pcs / carton |
| Primary Application | Roofing and related fastening applications |
The nails are connected by wire into a coil for continuous feeding through compatible pneumatic roofing nailers. This configuration allows a roofing nailer magazine to carry multiple fasteners and reduces the need to load individual loose nails during installation.
This roofing nail has a nominal length of 1-1/4 inches, approximately 32mm, and a nominal shank diameter of .120 inch, approximately 3.05mm. These dimensions are widely used within professional coil roofing nail systems.
The fasteners are connected in a 15-degree wire coil configuration. Buyers replacing nails for an existing roofing nailer should confirm the required collation type, angle, fastener length and shank diameter before ordering.
The wide full round head provides a broad bearing surface against roofing materials. This head configuration is commonly used for fastening shingles, underlayment and related roofing materials where a wide-head roofing nail is specified.
The KYA-3.05X32 product shown on this page uses a smooth shank. Smooth shank roofing nails are commonly used for asphalt shingle and general roofing fastening applications where this fastener specification is permitted.
The diamond point provides a conventional penetrating profile for driving through roofing materials and into a suitable wood substrate.
The electro-galvanized surface applies a zinc coating to the steel nail for corrosion protection. The correct coating should always be selected according to the roofing material, substrate, exposure conditions and applicable project requirements.
The current KYA specification lists 7,200 nails per carton, providing bulk packaging for contractors, roofing supply distributors, wholesalers and other professional buyers.
The 1-1/4" × .120" wire coil roofing nail configuration is intended primarily for roofing and related construction fastening. Actual suitability depends on the roofing system, substrate, required penetration and applicable installation requirements.
Asphalt shingle installation
Fiberglass shingle installation
Roofing felt
Roofing underlayment
Vapor barrier fastening
Insulation board attachment
Other roofing applications specifying compatible coil roofing nails
For roofing systems subject to specific building codes, manufacturer installation instructions or wind design requirements, select the nail length, head diameter, shank type, coating and fastening pattern according to those requirements.
Wire coil collation allows a roofing nailer to carry a relatively large number of fasteners in a compact magazine. This makes coil fasteners well suited to repetitive roofing installation where frequent fastening is required.
| Feature | 15° Wire Coil Roofing Nail | Loose Roofing Nail |
|---|---|---|
| Fastener Format | Wire-collated coil | Individual loose nails |
| Installation Equipment | Compatible pneumatic coil roofing nailer | Manual or other suitable installation method |
| Feeding | Automatic magazine feeding | Individual fastener handling |
| Product on This Page | 1-1/4" × .120" smooth shank | Not applicable |
The exact KYA-3.05X32 product shown on this page is a smooth shank roofing nail. Ring shank roofing nails are also available within the wider KYA roofing fastener range for applications that specify a ringed shank.
| Feature | Smooth Shank | Ring Shank |
|---|---|---|
| Shank Profile | Straight smooth surface | Annular rings along the shank |
| Typical Selection | General roofing fastening where smooth shank nails are specified | Applications requiring additional mechanical engagement with the substrate |
| Current Product | KYA-3.05X32 | Alternative configuration within the roofing nail range |
Shank selection should follow the roofing material manufacturer's instructions, project specification and applicable installation requirements rather than assuming one shank type is appropriate for every roof assembly.
The exact product shown on this page uses an electro-galvanized finish. KYA also lists other finishes and materials within the broader coil roofing nail range. Availability depends on nail length, shank configuration and required material.
| Finish / Material | Selection Consideration |
|---|---|
| Electro-Galvanized | Zinc-coated steel finish used on the KYA-3.05X32 product shown on this page. |
| Hot-Dip Galvanized | Available within selected KYA roofing nail configurations where a different galvanized coating is required. |
| Stainless Steel | Available within selected roofing nail sizes for applications specifying stainless steel fasteners. |
The appropriate fastener coating must be matched to the roofing material, wood substrate, environmental exposure and applicable installation specification. Confirm the required finish before placing a bulk order.
The KYA-3.05X32 is designed for compatible wire-coil roofing nailers that accept approximately .120 inch diameter roofing nails in the required length range. Tool compatibility should be confirmed from the complete fastener specification rather than the collation angle alone.
Professional roofing nailers from multiple manufacturers use this general fastener format. For example, BOSTITCH lists a 1-1/4" smooth shank 15-degree coil roofing nail within its roofing fastener range, SENCO lists a 1-1/4" × .120" 15-degree wire coil roofing nail, and MAX roofing nailers are available for 15-degree .120" wire coil roofing fasteners.
| Collation | 15° Wire Coil |
| Fastener Length | 1-1/4" (32mm) |
| Shank Diameter | .120" (3.05mm) |
| Shank | Smooth |
| Head | Full Round Wide Head |
| Required Tool | Compatible wire coil roofing nailer accepting the complete fastener dimensions |
| Before Ordering | Confirm tool manufacturer, model and accepted fastener specification |
Do not assume compatibility based only on a manufacturer's name or the term "roofing nailer." Different models can have different collation angles, nail lengths, head dimensions and magazine specifications.
KYA supplies roofing coil nails in multiple lengths within the .120 inch diameter range. The exact product on this page is the 1-1/4 inch smooth shank electro-galvanized configuration.
| Length | Shank Diameter | Collation | Series Availability |
|---|---|---|---|
| 3/4" (19mm) | .120" | Wire Coil | Available within roofing nail range |
| 7/8" (22mm) | .120" | Wire Coil | Available within roofing nail range |
| 1" (25mm) | .120" | Wire Coil | Available within roofing nail range |
| 1-1/4" (32mm) | .120" | 15° Wire Coil | Product shown on this page |
| 1-1/2" (38mm) | .120" | Wire Coil | Available within roofing nail range |
| 1-3/4" (45mm) | .120" | Wire Coil | Available within roofing nail range |
Available shank types, materials, finishes and packaging may vary by nail length. Confirm the complete specification for the required version before purchasing.
Roofing nail length should be selected according to the roofing material thickness, roof deck or substrate, required penetration and the installation requirements of the roofing system.
A longer nail is not automatically the correct choice. Professional buyers and installers should follow the roofing material manufacturer's installation instructions and applicable project requirements when determining the required fastener length.
For accurate product matching and quotation, provide the required nail length, shank diameter, shank type, finish, purchasing quantity, roofing nailer model and delivery destination.
For this product, reference KYA-3.05X32 and specify 1-1/4" × .120", smooth shank, 15° wire coil and electro-galvanized finish.
| Product Code | KYA-3.05X32 |
| Length | 1-1/4" / 32mm |
| Diameter | .120" / approximately 3.05mm |
| Shank | Smooth |
| Collation | 15° Wire Coil |
| Finish | Electro-Galvanized |
| Packing | 7,200 pcs / carton |
| Inquiry Information | Required quantity, roofing nailer model, application and delivery destination |
The KYA-3.05X32 has a nominal length of 1-1/4 inches, approximately 32mm, and a nominal shank diameter of .120 inch, approximately 3.05mm.
The exact KYA-3.05X32 product shown on this page is a smooth shank roofing nail. Ring shank versions are available within the wider KYA roofing nail range and should be specified separately when required.
It uses wire coil collation in a 15-degree configuration for compatible pneumatic coil roofing nailers.
Typical applications include asphalt shingles, fiberglass shingles, roofing felt, underlayment, vapor barriers and insulation board where a 1-1/4" × .120" roofing nail is appropriate for the specified roofing system.
The nail uses a full round wide head designed to provide a broad bearing surface against roofing material.
The KYA roofing nail uses a diamond point for penetration into suitable roofing materials and wood substrates.
The product shown on this page uses an electro-galvanized finish. Other coatings and stainless steel configurations are available within selected products in the wider KYA roofing nail range.
The current KYA specification lists 7,200 nails per carton for this product.
Several professional roofing nailers from these manufacturers use similar .120 inch wire coil roofing fasteners, but compatibility should be confirmed from the exact tool model, collation angle, accepted nail length, head dimensions and magazine specification before ordering.
No. Matching the angle alone is not sufficient. The nailer must also accept the correct collation material, fastener length, shank diameter, head size and coil configuration.
Fastener material and coating should be selected according to the roofing material, substrate, moisture exposure, environmental conditions and project requirements. Confirm the required specification before purchasing roofing nails for a particular installation.
Provide the required nail length, shank diameter, shank type, finish, quantity, roofing nailer manufacturer and model, application and delivery destination. Reference KYA-3.05X32 for this 1-1/4" × .120" smooth shank version.
Packaging configuration: 120 nails per coil, 60 coils per carton and 7,200 nails per carton.
Compatible nailer examples listed for this product include Bostitch RN46, Hitachi NV45AB2 and Senco RoofPro 445XP. Confirm the nail angle, wire collation, dimensions and tool manual for your exact nailer model before ordering.
Ring shank, hot-dip galvanized and stainless steel versions are also listed as available options. Specify the required shank and finish and confirm availability for the selected size.
A 7,200-piece sample carton is offered free of charge, with freight paid by the recipient. The listed minimum order quantity is 50 cartons (one pallet), and OEM branding is available. Confirm current sample availability, freight, MOQ and OEM requirements when requesting a quotation.
