| Material: | |
|---|---|
| Surface Treatment: | |
| Quantity: | |
KYA 15 Degree Electro-Galvanized Plastic Sheet Coil Nails in 1.80mm × 22mm / approximately .071" × 7/8" feature a ring shank, diamond point, full round head and plastic-sheet collation for compatible pneumatic coil nailing systems.
The featured model is KYA-1.8X22R. The current KYA product specification lists #45 steel, electro-galvanized finish, 15° plastic sheet collation and 300 nails per coil.
The 22mm leg length is substantially shorter than many conventional siding, fencing, sheathing and decking coil nails. This product should therefore be selected according to the actual material thickness, required penetration and nailer specification rather than by application name alone.
| Specification | Details |
|---|---|
| Model | 1.80 × 22mm |
| KYA Code | KYA-1.8X22R |
| Product Type | Plastic Sheet Collated Coil Nail |
| Shank Diameter | 1.80mm / .071 in. |
| Nail Length | 22mm / approximately 7/8 in. |
| Shank Type | Ring Shank |
| Point Type | Diamond Point |
| Head Type | Full Round Head |
| Material | Current KYA Specification: #45 Steel |
| Finish | Electro-Galvanized |
| Collation Type | Plastic Sheet |
| Collation Angle | 15° |
| Nails per Coil | 300 pcs |
| Tool Requirement | Compatible plastic-sheet coil nailer specifically rated for 1.8mm diameter and 22mm length |
| Recommended Selection Basis | Material thickness, required penetration, holding requirement and exact nailer specification |
Important: the 22–100mm length range, 1.8–4.0mm diameter range and 50–300 nails-per-coil range shown in KYA's broader product data describe a family of plastic-sheet coil nails. The featured SKU on this page is specifically 1.80 × 22mm with 300 nails per coil.
Request 1.8x22mm Coil Nail PricingDiamond Point
Ring Shank
Full Round Head
The annular rings along the shank increase mechanical engagement with surrounding wood fibers. In suitable wood substrates, this can provide greater resistance to nail back-out than a comparable smooth-shank nail.
The diamond point concentrates the driving force at the nail tip and supports penetration into compatible wood and wood-based substrates. Actual driving performance depends on material density, nailer power and fastener geometry.
The full round head provides a defined bearing surface against the fastened material. Exact head diameter should be confirmed where tool clearance or project specifications require a dimensional match.
Plastic-sheet collation uses a flexible plastic carrier to hold multiple nails in a coil at a controlled angle for automatic feeding through a compatible pneumatic nailer.
During driving, the nail separates from the carrier. Unlike wire-weld collation, the product is not held together by welded metal wires. Tool selection must therefore match both the 15° angle and the plastic-sheet carrier system.
Do not describe this product as “15° wire collated.” It is specifically a 15° plastic sheet collated coil nail.
The 22mm leg can be considered for selected thin wood, plywood, panel and board assemblies where the material thickness and receiving substrate provide suitable penetration for a 1.8mm ring-shank fastener.
Short ring-shank coil nails can be useful for suitable trim, accessory and light assembly applications where increased resistance to back-out is desirable but a long construction nail would provide excessive penetration.
Selected light crate, box and packaging assemblies may use short ring-shank coil nails where the receiving material is thick enough for the 22mm fastener and increased withdrawal resistance is required.
OEM wood-product manufacturers can use the 1.8×22mm configuration in products specifically designed around this short fastener size. When replacing another nail, provide the existing fastener drawing and nailer model.
This nail should only be used in siding or exterior components when the manufacturer's fastening specification explicitly permits a 22mm nail and electro-galvanized finish. Many conventional siding systems require substantially longer fasteners and stronger corrosion protection.
Application names alone are not enough to select a coil nail. A 22mm / approximately 7/8-inch nail is considerably shorter than many conventional siding, fencing, decking and structural sheathing fasteners.
| Application | 1.8x22mm Selection Guidance |
|---|---|
| Thin Panels / Light Wood | Relevant where 22mm total length provides the required penetration |
| Trim / Accessories | Can be considered where a short ring-shank fastener is specified |
| Siding | Use only if the siding system specifically permits this nail length and finish |
| Fencing | Generally verify carefully because many fence applications require substantially longer fasteners |
| Decking | Do not assume suitability; conventional deck fastening generally requires greater penetration |
| Roof / Wall Sheathing | Do not use for structural fastening unless the approved fastening schedule specifically requires this size |
| Subfloor | Do not assume suitability; follow the flooring or structural fastening specification |
Electro-galvanizing applies a zinc coating to the steel fastener and provides more corrosion protection than untreated bright steel. It is commonly selected for interior, sheltered and limited-moisture applications.
For continuous outdoor exposure, treated lumber, coastal environments or other corrosive conditions, confirm whether hot-dip galvanized or stainless steel fasteners are required by the application specification.
| Finish | General Selection |
|---|---|
| Electro-Galvanized | Interior, sheltered or limited-moisture use depending on specification |
| Hot-Dip Galvanized | Higher corrosion protection where HDG fasteners are specified for exterior use |
| Stainless Steel | Higher corrosion resistance for demanding wet, coastal or corrosive environments according to grade and project requirements |
The broader KYA coil nail family includes diamond, chisel, blunt, clinch and round point configurations. The featured 1.8×22mm product on this page is shown with a diamond point. Alternative point styles should be confirmed for the exact size before ordering.
| Shank | General Characteristic | Selection |
|---|---|---|
| Ring Shank | Annular rings increase engagement with wood fibers and resistance to backing out | Featured configuration on this 1.8×22mm page |
| Smooth Shank | Smooth profile supports easier driving with lower withdrawal resistance in comparable wood | General fastening where additional ring-shank hold is not required |
| Screw Shank | Twisted profile rotates during driving into suitable wood | Selected pallet, hardwood and industrial fastening applications |
KYA supplies a broader range of plastic-sheet coil nails with different diameters, lengths, heads, points, shanks, finishes and coil capacities. The values below describe family options and should not be interpreted as specifications of every individual SKU.
| Family Parameter | Current KYA Listed Range / Options |
|---|---|
| Length | 22–100mm in current page family data; this SKU is specifically 22mm |
| Wire Diameter | 1.8–4.0mm; this SKU is specifically 1.8mm |
| Head Diameter | 5.0–9.2mm family range; confirm exact head diameter for the 1.8×22mm SKU |
| Shank | Ring, Smooth, Screw depending on product |
| Point | Diamond, Chisel, Blunt, Clinch, Round depending on product |
| Collation | Plastic Sheet; 0° or 15° configurations within the wider range |
| Coil Capacity | 50–300 nails per coil across current family data; this SKU is listed as 300 |
| Finish | Electro-Galvanized, Hot-Dip Galvanized, Bright and other product-specific options |
Do not assume that a nail fits a tool because both products are described as 15-degree coil systems. Tool compatibility depends on the complete fastener specification.
| Compatibility Parameter | This Product |
|---|---|
| Collation Angle | 15° |
| Collation Type | Plastic Sheet |
| Shank Diameter | 1.80mm / .071 in. |
| Nail Length | 22mm / approx. 7/8 in. |
| Shank Type | Ring Shank |
| Head | Full Round Head; confirm exact diameter |
| Coil Capacity | 300 pcs |
| Required Tool | Tool whose manufacturer explicitly permits this diameter, length and plastic-sheet carrier geometry |
The previous page listed MAX CN55, Hitachi NV65AH, Bostitch N80CB and Senco SCN65 as compatible tools. These references should not be retained without model-specific verification because common tools in these families generally use larger-diameter and longer nails than this 1.8×22mm product.
| Purchasing Information | Required Detail |
|---|---|
| Size | 1.80 × 22mm |
| Shank | Ring Shank |
| Point | Diamond Point |
| Collation | 15° Plastic Sheet |
| Finish | Electro-Galvanized |
| Coil Quantity | 300 nails per coil |
| Nailer Model | Provide exact manufacturer and model for compatibility confirmation |
| Application | Provide material type, thickness and required penetration |
| Environment | Interior, sheltered, exterior, coastal or other exposure condition |
| Quantity | Coils, cartons, pallets or annual purchasing volume |
The featured product is 1.80mm in shank diameter and 22mm long, approximately .071 inch × 7/8 inch.
The current KYA model code is KYA-1.8X22R.
The annular rings increase engagement with surrounding wood fibers and can provide greater resistance to withdrawal than a comparable smooth-shank nail in suitable wood.
The original page used a 40% figure, but the supplied product data does not include the wood species, test method, penetration depth or comparison fastener required to verify that exact percentage. It is more accurate to state that ring shanks generally improve withdrawal resistance in suitable wood.
The nails are held in a 15° coil using a plastic carrier for automatic feeding through a compatible nailer. This is different from wire-weld collation.
The current KYA product listing specifies 300 nails per coil for this 1.8×22mm product.
Do not assume suitability based only on the term “siding nail.” A 22mm nail is much shorter than many conventional siding fasteners. Use it only when the siding manufacturer or installation specification permits this nail length, diameter, head and corrosion-protection level.
Most conventional structural decking applications require greater fastener penetration. This 22mm product should only be used where the specific assembly calls for a short fastener of this size.
Do not use this SKU for structural sheathing or subfloor fastening unless the approved fastening schedule explicitly specifies a 1.8×22mm fastener.
Electro-galvanized nails provide basic zinc corrosion protection. For long-term outdoor exposure, treated lumber, coastal locations or other corrosive conditions, confirm whether hot-dip galvanized or stainless steel is required.
The standard MAX CN55 specification is for larger wire-collated nails, so it should not be listed as a confirmed match for this 1.8mm plastic-sheet nail. Always compare the exact tool specification before use.
No. The angle alone does not establish compatibility. Collation material, nail diameter, length, head dimensions, coil geometry and magazine design must also match.
The plastic carrier separates as the nails are driven. It is more accurate to describe the system as a plastic-sheet carrier that detaches during fastening rather than claiming absolutely zero plastic debris in every tool and application.
Provide the nailer model, required quantity, application, material thickness, corrosion environment, packaging requirements and destination market.
Contact KYA regarding current sample availability. For production evaluation, test the exact nail with the intended nailer and actual substrate before bulk purchasing.
KYA supplies plastic-sheet coil nails for fastener distributors, pneumatic-tool distributors, wood-product manufacturers, packaging factories and professional fastening buyers.
For quotations on 1.8×22mm 15° electro-galvanized ring-shank plastic sheet coil nails, provide the exact nailer model, application, required quantity, packaging and destination market.
Request a Bulk Quote View More Coil Nails
