| Head: | |
|---|---|
| Finish: | |
| Degree: | |
| Quantity: | |
KYA 34° paper tape collated joist hanger nails are designed for fastening pre-punched metal connectors to wood, including joist hangers, straps, anchors, seismic ties and hurricane ties. The range includes commonly used connector-nail diameters such as .131" and .148", with head-stamped identification and full round head configurations.
The featured .148" × 1-1/2" configuration is a common short metal-connector nail size, while longer versions up to 2-1/2" are available within the KYA range for applications that require deeper penetration. Select nail diameter, length, shank and finish according to the exact connector manufacturer's fastening schedule.
34° paper tape collation: designed for compatible angled-strip metal connector nailers.
Head-stamped identification: helps installers and inspectors identify the installed fastener.
Full round head: designed for structural metal connector fastening applications.
.131" and .148" diameter options: common connector-nail dimensions for different hardware and fastening schedules.
1-1/2" and longer configurations: available for connector applications requiring different penetration depths.
Diamond point: designed for efficient penetration into compatible wood substrates.
Multiple finish options: electro-galvanized, hot-dip galvanized and stainless steel configurations are available within the KYA range.
| Parameter | Specification |
|---|---|
| Product Type | Joist Hanger Nail / Metal Connector Nail |
| Collation Angle | 34° nominal |
| Collation Type | Paper Tape Collated |
| Head Type | Full Round Head |
| Head Identification | Head Stamped |
| Diameter Options | .131" / approximately 3.33 mm; .148" / approximately 3.76 mm |
| Length Range Listed on Page | 1-1/2"–2-1/2" / approximately 38–64 mm depending on specification |
| Shank Options | Smooth / Ring depending on size |
| Point | Diamond Point |
| Finish Options | Electro-Galvanized / Hot-Dip Galvanized / Stainless Steel depending on specification |
| Typical Applications | Joist hangers, straps, anchors, metal connectors, seismic ties and hurricane ties |
KYA lists multiple 34° paper-collated metal connector nail sizes. The exact fastener must be selected according to the connector manufacturer's approved or specified nail schedule.
| Diameter | Length | Head | Shank | Finish | Page-Listed Box Qty |
|---|---|---|---|---|---|
| .148" / 3.76 mm | 1-1/2" / 38 mm | Full Round | Smooth | EG / HDG | 1,000 / 2,000 pcs |
| .131" / 3.33 mm | 1-1/2"–2-1/2" | Full Round | Smooth / Ring | EG / HDG / SS304 | 1,000–2,000 pcs |
| .148" / 3.76 mm | 2-1/2" / 64 mm | Full Round | Smooth | EG / HDG | 1,000 pcs |
Box quantities and available finish combinations can vary by nail size. Confirm the exact diameter, length, material, finish and packing configuration with the quotation.
Joist hangers, straps, anchors and other structural connectors are engineered around specific fastener dimensions and installation patterns. A metal connector nail is selected according to the connector manufacturer's specified diameter, length, head type, shank configuration and corrosion protection.
Standard framing nails should not automatically be substituted for connector nails simply because they fit through the connector hole. Using a different nail diameter, length or head configuration can change the performance of the connection.
The .148" × 1-1/2" size is a widely used metal connector nail format for applications requiring a short, larger-diameter fastener. Current professional metal connector fastener systems from SENCO, Paslode and Metabo HPT include .148" × 1-1/2" configurations for joist hangers, straps, anchors and related hardware.
However, this does not mean that .148" × 1-1/2" can be used in every connector. Always use the fastener size listed for the exact hanger, tie, strap or anchor being installed.
Longer 2-1/2" metal connector nails are used in selected structural connector applications where greater penetration is specified. Professional 2-1/2" metal connector nailers are designed to accommodate longer fasteners while maintaining accurate placement into pre-punched connector holes.
Do not replace a specified 1-1/2" connector nail with a 2-1/2" nail, or vice versa, unless the connector manufacturer's installation table permits the substitution.
The KYA range includes head-stamped metal connector nails. Head marking allows the installed fastener to be identified more easily after it has been driven into the connector.
Head stamping is widely used by professional connector-nail manufacturers because inspection often requires confirmation that the specified fastener type has been installed.
Paper tape holds the connector nails in angled strips for feeding through compatible pneumatic metal connector nailers. The collation separates as the nail is driven, while the exposed or locating nose of a metal connector nailer helps position the nail point into the pre-punched connector hole.
Collation angles used by professional connector systems can vary slightly by manufacturer. Tools may be specified at approximately 34°, 35° or 36°, so compatibility should be determined from the actual tool and fastener specifications rather than angle terminology alone.
Joist hangers: fastening compatible wood construction connectors to supporting members.
Hurricane ties: fastening structural ties where the connector manufacturer specifies compatible metal connector nails.
Seismic ties: fastening connector hardware used in engineered lateral-force-resisting assemblies.
Straps: installation of structural straps and related metal framing hardware.
Anchors: fastening selected wood-to-metal connector assemblies.
Truss connectors: installation of compatible engineered wood and roof-framing hardware.
Residential framing: structural connector installation where the specified fastener matches the hardware schedule.
Commercial wood construction: metal-to-wood connector applications using specified structural nails.
Request Connector Nail Specifications
The connector manufacturer's installation schedule should be the primary reference when selecting a joist hanger nail. Check the exact hardware model because different connectors can require different nail diameters and lengths at the header, joist, flange or web locations.
| Selection Item | What to Confirm |
|---|---|
| Nail Diameter | Use the diameter specified for the exact connector, such as .131" or .148" where applicable. |
| Nail Length | Confirm required penetration and whether 1-1/2" or a longer nail is specified. |
| Head Type | Use the head configuration required for the structural connector installation. |
| Shank Type | Confirm whether smooth or ring shank is specified. |
| Finish | Match corrosion resistance to connector coating, treated lumber and exposure conditions. |
| Tool Compatibility | Confirm paper strip angle, nail diameter, nail length and magazine requirements. |
Structural connector fasteners must be selected with corrosion compatibility in mind. KYA lists electro-galvanized, hot-dip galvanized and stainless steel versions within its joist hanger nail range.
| Finish / Material | Selection Consideration |
|---|---|
| Electro-Galvanized | Zinc-coated steel for applications where this corrosion-protection level is permitted. |
| Hot-Dip Galvanized | Used where a heavier galvanized coating is required for the connector, lumber treatment or exposure condition. |
| Stainless Steel | Available within the broader KYA connector-nail range for applications requiring greater corrosion resistance. |
The fastener finish should be compatible with the metal connector and wood treatment. For exterior, coastal or treated-lumber applications, follow the connector manufacturer's corrosion and material recommendations.
Professional metal connector nailers use a locating nose or exposed fastener point to help place the nail into the pre-punched hole. Similar systems can use slightly different strip angles and dimensional ranges.
| Tool Family | Published Fastener Reference |
|---|---|
| SENCO JN91H1 / JN91H2 | 34° paper tape metal connector nails; 1-1/2" connector fasteners. |
| SENCO JN91P1 / JN91P2 | 34° paper tape metal connector nails from 1-1/2" to 2-1/2", depending on fastener diameter. |
| Bostitch MCN150 | Approximately 35° paper-collated metal connector nails; 1-1/2" length with .131" and .148" diameters. |
| Bostitch MCN250 / MCN250S | Approximately 35° paper-collated metal connector nails in 1-1/2" and 2-1/2" lengths. |
| Metabo HPT NR38AK | 36° paper-strip metal connector nails, 1-1/2", .131"–.148" diameter. |
| Metabo HPT NR65AK2 Series | 36° paper-strip metal connector system for 1-1/2" and 2-1/2" fasteners. |
Because nominal strip angles vary between manufacturers, do not assume universal compatibility. Compare paper-strip geometry, nail diameter, nail length, head dimensions and magazine specification with the exact nailer before ordering.
Paslode Positive Placement metal connector systems use a 30° fastener format. Their 1-1/2" and 2-1/2" metal connector nails are purpose-designed for Paslode Positive Placement tools.
For that reason, a 34° KYA paper strip should not be advertised as universally interchangeable with Paslode 30° metal connector fasteners. Buyers using Paslode tools should provide the exact tool model before compatibility is confirmed.
ASTM F1667 establishes dimensional and performance requirements for driven fasteners used in wood construction, including fastener categories used with structural hardware.
When ASTM F1667 compliance, an evaluation report or another project-specific approval is required, request documentation for the exact KYA nail specification being supplied. Nail diameter, length or head style alone should not be treated as proof that a particular product carries a specific third-party approval.
Structural connector manufacturers publish specific fastener schedules for each connector model. Simpson Strong-Tie, MiTek and other connector manufacturers can specify different nail diameters, lengths and quantities depending on the hardware and connection.
Do not assume that one .148" × 1-1/2" nail is suitable for every joist hanger, hurricane tie, strap or hold-down. Verify the exact connector installation table before substituting or purchasing fasteners.
For quotations, provide the required diameter, length, shank type, finish, quantity, destination market, connector application and nailer model. If the project specifies a particular connector brand, evaluation report, corrosion class or fastener standard, include that information with the inquiry.
The current KYA page lists an MOQ of 50 boxes and indicates that samples can be arranged. Confirm the current MOQ, sample quantity, freight arrangement and packing configuration when requesting pricing.
They are designed for fastening compatible joist hangers, structural straps, anchors, seismic ties, hurricane ties and other pre-punched metal connectors to wood.
Common metal connector nail systems include diameters such as .131" and .148". The exact diameter must match the connector manufacturer's specified fastener schedule.
Yes. .148" × 1-1/2" is a widely used metal connector nail size and appears in professional connector-nail systems from multiple manufacturers. It should still only be used where that size is specified for the exact connector.
Yes, when the selected nail diameter, length, head, shank and finish match the fastener requirements for the exact joist hanger being installed.
They can be used with hurricane ties and similar connectors when the tie manufacturer's installation schedule specifies a compatible metal connector nail. Do not assume that one nail size applies to every hurricane tie model.
Yes. The KYA product information lists head-stamped identification, which helps identify the fastener after installation.
A specific ICC-ES approval should only be claimed when the exact KYA product is identified in the applicable current evaluation report. If an evaluation report is required for your project, request the corresponding documentation before ordering.
No. Evaluation reports identify specific report holders, listees and recognized fasteners. A similar nail size or paper-tape format does not automatically make another manufacturer's product covered by that report.
SENCO JN91 metal connector nailers are designed for 34° paper tape metal connector nails. Confirm the exact JN91 model and the required nail diameter and length before ordering.
The Bostitch MCN150 is specified for approximately 35° paper-collated, 1-1/2" metal connector nails in .131" and .148" diameters. Confirm the actual strip geometry and nail dimensions before use.
The NR38AK uses approximately 36° paper-strip, 1-1/2" metal connector nails from .131" to .148". Because the nominal collation angle differs slightly, verify the exact strip geometry before ordering.
Paslode Positive Placement metal connector nailers are specified around a 30° fastener system. Do not assume a 34° paper strip is compatible without confirmation for the exact Paslode tool and nail configuration.
A dedicated metal connector nailer is preferred because its locating nose is designed to position the nail into pre-punched connector holes. A standard framing nailer should only be used if its manufacturer specifically permits the required metal connector fastener and installation method.
Use a finish or material that is compatible with both the wood treatment and the connector coating. Hot-dip galvanized or stainless steel fasteners may be required depending on the connector manufacturer's corrosion guidance and the exposure environment.
Stainless steel options are listed within KYA's broader joist hanger nail range. Confirm the required stainless grade, diameter, length and connector compatibility when requesting a quotation.
Provide the required nail diameter, length, shank type, finish or material, quantity, destination market, metal connector model and nailer model. Include any required evaluation report or construction specification.
KYA supplies 34° paper tape collated joist hanger and metal connector nails for fastener distributors, connector suppliers, framing contractors and professional construction users. Send the required diameter, length, finish, quantity, connector application and nailer model to confirm the appropriate fastener configuration.
