Pneumatic Hog Ringer C-660

C-660 Pneumatic Hog Ringer for 16GA C-Rings

KYA C-660 is an industrial pneumatic hog ringer designed for 16 gauge C-style hog rings used in mattress production, automotive upholstery, furniture, wire cages, fencing, netting, bag closure and other repetitive fastening applications.

The tool weighs approximately 1.74kg and uses a 125-ring magazine. It is designed for C-rings with approximately 16.9mm outside crown, 12.5mm / 1/2 inch inner crown, 1.6mm wire and approximately 3.0mm finished closure.

The C-660 belongs to the common 16GA SC660 / C17 / 516-type pneumatic C-ring class. Fastener compatibility should be confirmed by outside crown, inner crown, wire diameter, ring height, closure and strip geometry rather than by gauge alone.

C-660 Pneumatic Hog Ringer Specifications

16GA 16.9mm C-Ring Fastener System

The C-660 is designed around a common 16 gauge pneumatic C-ring format. The fastener has an approximately 16.9mm outside crown, 12.5mm inner crown and 1.6mm wire diameter.

This format is widely described under fastener references such as C17, SC660 and 516-type rings. The naming system can vary between manufacturers, so the actual ring dimensions should always be compared before substitution.

1/2 Inch Inner Crown and 5/8 Inch Outer Crown

The same C-ring can be described using two different crown measurements. Approximately 12.5mm / 1/2 inch refers to the inner open crown, while approximately 16.9mm / 5/8 inch refers to the outside crown.

Buyers should check both dimensions because product listings that use only one crown measurement can make two different C-ring systems appear similar.

1.6mm / 16 Gauge Wire

Compatible C-rings use approximately 1.6mm wire, corresponding to the standard 16 gauge SC660 / C17 fastening class.

Wire diameter is important for both magazine feeding and ring forming. A ring with a similar crown but 1.8mm wire belongs to a different fastener class and should not automatically be used in the C-660.

Approx. 3.0mm Ring Closure

KYA lists the C-660 with an approximately 3.0mm closure. Comparable 16GA 16.9mm pneumatic C-ring tools commonly operate in a range of approximately 2.6–3.6mm.

The correct closure depends on the diameter of the wire, spring, fabric, mesh or other material being captured by the ring. The smallest possible closure should not automatically be considered the best setting for every application.

125-Ring Magazine

The C-660 holds approximately 125 compatible C-rings, allowing longer fastening runs between reloads compared with smaller-capacity pneumatic ring tools.

For reliable feeding, use correctly collated strips and avoid loading bent, damaged or incorrectly sized rings.

Ergonomic Pneumatic Design

The C-660 uses a balanced pneumatic tool layout with a rubber grip for repetitive fastening. At approximately 1.74kg, the tool is intended for production environments where operators perform repeated ring-closing cycles.

Balanced handling and pneumatic operation can reduce the manual force required compared with hand pliers, although operator comfort also depends on workstation height, hose routing, production rate and shift length.

High-Strength Alloy Steel Muzzle

KYA specifies a high-strength alloy steel muzzle for the C-660. The jaws and muzzle guide the ring during feeding and control the final closing shape.

These components should be checked periodically for wear, contamination or misalignment because jaw condition directly affects ring closure and feeding consistency.

Compatible C-Ring References

C-660 vs 15GA C7-Type Hog Ring Tools

Do not substitute 15GA C7, HR23 or 15G100-type rings into the C-660. They use a larger 1.8mm wire and a substantially larger crown.

C-660 for Mattress Manufacturing

The C-660 can be used in mattress and bedding production for fastening compatible spring, border wire, fabric and related components where the 16GA C-ring and approximately 3mm closure are suitable.

Production teams should confirm the finished closure around the actual spring or wire combination before repetitive use.

C-660 for Automotive Upholstery

Pneumatic C-ring tools are widely used to join compatible seat wire, upholstery components and frame elements in automotive seating and furniture production.

The required ring material, point type and closure should be selected according to the wire bundle, fabric and seat construction rather than using one universal setup.

C-660 for Wire Cages and Fencing

The 16GA C-ring class is also used for pet cages, animal enclosures, wire mesh, fencing and related wire-joining applications.

Select galvanized, stainless-steel or another specified ring material according to indoor or outdoor exposure, moisture and corrosion requirements.

C-660 for Bag Closure and Netting

C-rings can be used for selected bag closure, netting and mesh assembly where the material bundle fits correctly inside the closed ring.

Sharp or blunt-point ring configurations should be chosen according to whether the fastener needs to penetrate material during installation.

Typical C-660 Applications

• Spring mattress manufacturing

• Automotive seat upholstery

• Furniture upholstery

• Pet and animal cages

• Wire mesh

• Fencing

• Netting

• Wire connections

• Bag closure

• Selected cord and fabric fastening

Galvanized vs Stainless Steel C-Rings

Confirm the required ring material according to the actual service environment. Stainless steel grade and coating specification should be verified when corrosion resistance is a project requirement.

Air Supply and Tool Setup

KYA lists the C-660 operating range at approximately 4–7 bar / 58–102 PSI. Use regulated, clean compressed air and operate within the specified range.

If a ring does not close correctly, check fastener dimensions, jaw condition, feed alignment and air pressure rather than simply increasing pressure.

C-660 Maintenance Checklist

• Inspect closing jaws and muzzle surfaces regularly.

• Keep the magazine and ring feed path clean.

• Use correctly collated 16GA 16.9mm C-rings.

• Check hose connections and fittings for air leakage.

• Do not use bent or damaged fastener strips.

• Disconnect compressed air before clearing jams or servicing the tool.

• Replace worn jaws if ring closure becomes inconsistent.

Bulk Orders for Industrial Production

KYA supplies pneumatic hog ring tools and matching C-rings for mattress factories, automotive seating suppliers, furniture manufacturers, cage producers, fencing suppliers and industrial fastener distributors.

For bulk purchasing, provide the required tool quantity, current fastener model, ring material, ring dimensions, desired closure, application and compressed-air specification.

KYA Pneumatic Hog Ring Tools

KYA supplies pneumatic C-ring and D-ring tools in multiple gauges, crown sizes, magazine capacities and closure configurations for mattress, upholstery, automotive, cage, fencing and industrial fastening applications.

Frequently Asked Questions About C-660

What rings fit the C-660 hog ringer?

The C-660 is designed for 16 gauge C-rings with approximately 16.9mm outside crown, 12.5mm inner crown, 1.6mm wire and approximately 3mm closure.

Is the C-660 a 1/2 inch hog ring tool?

Yes. The compatible ring has an approximately 1/2 inch inner crown and 5/8 inch / 16.9mm outside crown.

What gauge does C-660 use?

It uses the 16 gauge C-ring class with approximately 1.6mm wire.

What is the closure diameter?

KYA lists an approximately 3.0mm closure. Comparable 16GA tools commonly close this ring class to approximately 2.6–3.6mm.

How many rings does C-660 hold?

The C-660 magazine holds approximately 125 compatible C-rings.

How much does C-660 weigh?

KYA lists the tool at approximately 1.74kg / 3.84lbs.

What air pressure does C-660 require?

KYA lists approximately 4–7 bar / 58–102 PSI.

Can C-660 use C17 hog rings?

C17 is a common reference for the same general 16GA 16.9mm crown C-ring class. Confirm actual ring height, strip geometry and closure before bulk use.

Can C-660 use SC660 rings?

SC660 is another market reference for this 16GA C-ring size. Confirm the complete fastener dimensions before substitution.

Can C-660 use 516G100 hog rings?

516G100 belongs to the same general 16GA 1/2-inch inner-crown / 16.9mm outer-crown C-ring class. Verify collation and target closure with the exact tool before production use.

Can C-660 use 15G100 or HR23 rings?

No direct interchangeability should be assumed. 15G100 and HR23 are generally 15GA 1.8mm C-rings with substantially larger crowns.

Can C-660 be used for mattress manufacturing?

Yes. Spring mattress and bedding production are established applications for 16GA C-ring tools when the ring closure matches the spring and wire combination.

Can C-660 be used for automotive seats?

Yes. Automotive seating and upholstery are common applications when the 16GA C-ring geometry matches the seat components being joined.

Can C-660 be used for cages and fencing?

Yes. Wire cages, mesh and fencing are suitable applications where the finished ring diameter fits the wire combination.

Can stainless-steel C-rings be used?

Stainless-steel rings are available in the 16GA 16.9mm C-ring class. Confirm wire diameter, strip geometry and material specification before use.

Does the ergonomic design eliminate operator fatigue?

No. Balanced pneumatic operation can reduce manual effort, but fatigue also depends on workstation ergonomics, hose arrangement, fastening frequency and shift duration.

What information should I provide before ordering?

Provide the application, quantity, current tool or ring model, ring material, outside and inside crown, wire diameter, target closure and available compressed-air specification.