KYA RR1-5/8 Coil Carton Staples are steel roll staples designed for carton closing and corrugated packaging applications. The featured RR1-5/8 configuration uses a 1-1/4-inch / 31.75mm crown and a 5/8-inch nominal leg, with copperized or galvanized surface-finish options.
The current KYA specification identifies a chisel point and glue-collated coil format. The product is intended for compatible RR-type roll carton stapling systems used to close corrugated shipping cartons and other packaging boxes.
For replacement applications, match more than the RR name alone. Confirm the 1-1/4-inch crown, 5/8-inch leg, coil capacity, feed geometry, point type and exact stapler model before changing from another supplier's roll staple.
| Specification | Details |
|---|---|
| Product Type | Roll / Coil Carton Closing Staple |
| Model | RR1-5/8 |
| KYA Code | KYA-RR1-5/8 |
| Material | Steel |
| Surface Finish | Copperized or Galvanized |
| Crown | 1-1/4" / 31.75mm |
| Leg Length | 5/8" nominal; current KYA page also references 15mm |
| Point Type | Chisel Point |
| Collation | Glue-Collated Coil / Roll |
| Current Published Coil Options | 1,000 pcs/coil or 5,000 pcs/coil; confirm RR1 / RR5 designation for the required packing format |
| 1,000-Piece Packing | 1,000 pcs/coil, 24 coils/carton according to the current KYA table |
| 5,000-Piece Packing | 5,000 pcs/coil, 6 coils/carton according to the current KYA table |
| Wire Gauge | Not stated consistently across current KYA sources; confirm the production drawing before publishing a gauge value |
| Primary Application | Closing and securing corrugated cartons in packaging operations |
Specification note: this page should use 1-1/4" / 31.75mm as the primary crown specification. Do not confuse RR-type 1-1/4" crown staples with SWC7437-type carton staples that commonly use a 1-3/8" crown.
RR1-5/8 is an industry designation used for a roll carton-closing staple with a 1-1/4-inch crown and 5/8-inch leg. Current ISM and Spotnails RR-family references use the RR1 designation for the 1,000-staple roll format.
For GEO clarity, this URL should therefore remain centered on RR1-5/8 rather than treating every RR roll-staple configuration as the same exact SKU.
The current KYA page publishes both 1,000-piece and 5,000-piece coil formats. Industry RR-family references commonly distinguish those capacities through RR1 and RR5 naming, so the coil capacity should be confirmed when cross-referencing another brand.
| Industry RR Reference | Leg Length | Typical Coil Capacity | Current KYA Guidance |
|---|---|---|---|
| RR1-5/8 | 5/8" | 1,000 staples/roll in current ISM and Spotnails references | Primary entity for this page |
| RR5-5/8 | 5/8" | 5,000 staples/roll in current Spotnails RR-family reference | KYA currently also publishes a 5,000-piece coil format; confirm whether it should be designated RR5-5/8 on the purchase specification |
| RR1-3/4 | 3/4" | 1,000 staples/roll in current RR-family references | Longer-leg related RR configuration; not the featured 5/8" SKU |
| RR5-3/4 | 3/4" | 5,000 staples/roll in current RR-family references | Longer-leg / higher-capacity related configuration |
Data-quality note: the current KYA page also lists RR178 and RR578 in its broader “Types” field while the same table describes the length range as only 5/8" to 3/4". Because no 7/8" specification is provided on this page, 7/8" RR variants should not be added to this product's technical data without separate confirmation.
The RR1-5/8 uses a 1-1/4-inch crown. This wide carton-closing format spans the carton flap or seam and is intended for dedicated roll carton staplers designed around the RR staple geometry.
Crown width is one of the most important compatibility parameters. A 1-1/4-inch RR staple should not be confused with a 1-3/8-inch SWC carton staple merely because both are used for carton closing.
The featured RR1-5/8 uses a 5/8-inch nominal leg. KYA also references 15mm in its metric product data. When cross-referencing tooling or another supplier, use the manufacturer's stated RR1-5/8 specification rather than treating 15mm and the mathematical inch conversion as automatically identical.
Whether 5/8" is the correct leg length depends on the corrugated-board construction, number of material layers being closed and the adjustment range of the carton stapler.
The current KYA product table specifies a chisel point. Current Spotnails RR-family carton staples also use a chisel-point specification for the corresponding 1-1/4-inch crown roll format.
The staples are glue collated into a roll for continuous magazine feeding. Coil capacity and feed geometry must match the carton stapler. Do not assume that a 5,000-piece roll can be loaded into a tool designed around a 1,000-piece roll system.
| Finish | Current KYA Information | Ordering Guidance |
|---|---|---|
| Copperized | Listed as a current surface-finish option | Specify copperized when matching an existing RR staple or customer packaging specification |
| Galvanized | Listed as a current surface-finish option | Specify galvanized when required by the existing carton-closing specification |
The current KYA page does not publish coating thickness, salt-spray hours or a defined environmental exposure class for either finish. Those performance values should not be added without the applicable technical specification.
The current KYA page references ISM RA1000T 5/8, RA1000T 3/4 and JK special models. Independent RR-family specifications also show that the 1-1/4-inch crown RR system is used across several carton-stapler families. These references are useful for identification, but exact KYA compatibility should be confirmed from the stapler and staple dimensions before production use.
| Tool / System Reference | Published RR Information | KYA Matching Guidance |
|---|---|---|
| ISM RR1-5/8 | Current ISM Direct listing: 1-1/4" crown, 5/8" leg, 1,000 staples/roll, 24 rolls/case | Strong dimensional reference for RR1 naming; confirm KYA feed geometry before substitution |
| Spotnails CCRR1-5/8 | 1-1/4" crown, 5/8" leg, galvanized, chisel point, roll collation, 1,000/roll ×24 | Useful RR1-family cross-reference; not proof of universal interchangeability with every KYA finish or coil configuration |
| Spotnails KSR3219R | Published for 1-1/4" crown RR-type carton closing roll staples from 5/8" to 3/4" | RR-family tool reference; verify the exact KYA staple before volume use |
| ISM RA / RC 1000T Family | Referenced by KYA and RR-family suppliers for roll carton-closing staples | Check the exact 5/8" or 3/4" tool setup, crown and roll format before ordering |
| JK / Josef Kihlberg RR-Type Systems | RR-family cross-references exist in current carton-staple tables | Provide the exact tool model; do not rely on the JK brand name alone |
Gauge note: current KYA sources are not consistent enough to publish a definitive RR1-5/8 wire-gauge value on this page. Tool compatibility should therefore be based on the complete RR staple dimensions and feed specification rather than a gauge label alone.
RR1-5/8 roll staples are intended for closing corrugated cartons with a compatible roll carton stapler. The 1-1/4-inch crown spans the carton seam while the legs are clinched through the corrugated material by the stapling system.
The current KYA page lists shipping and packaging cartons as primary applications. Select the staple leg and stapler adjustment according to the corrugated-board construction being closed.
Coil-fed carton staples are used where a roll-fed closing tool is part of a packaging process. Coil capacity affects reload frequency, but the stapler must be designed for the selected roll capacity.
| Specification | RR1-5/8 | Typical SWC7437-Type Roll Staple |
|---|---|---|
| Crown | 1-1/4" | Commonly 1-3/8" |
| Featured Leg | 5/8" | Multiple leg lengths including 5/8" exist |
| Family | RR | SWC / CCBR-type |
| Interchangeable? | No. Different crown dimensions require the correct carton-stapler system. | |
| Selection Factor | What to Check |
|---|---|
| Corrugated Board Construction | The total thickness of the carton flaps being closed affects the required staple leg. |
| Stapler Setup | Verify whether the tool is configured for a 5/8" or 3/4" RR staple and adjust the clinch system according to the tool instructions. |
| Crown Family | Confirm that the tool uses the 1-1/4" RR family rather than a different carton-staple crown. |
| Coil Capacity | Confirm whether the tool accepts 1,000-piece, 5,000-piece or another specified roll format. |
| Current Staple Reference | When replacing another brand, provide the existing RR / CCRR part number and exact stapler model. |
| Ordering Information | What to Provide |
|---|---|
| Model | RR1-5/8 / KYA-RR1-5/8 |
| Crown | 1-1/4" / 31.75mm |
| Leg | 5/8" nominal |
| Finish | Specify Copperized or Galvanized |
| Coil Capacity | Specify required roll capacity and confirm whether the order should use RR1 or RR5 designation |
| Current Staple | Provide the current RR / CCRR product number if replacing another supplier |
| Carton Stapler | Provide exact manufacturer and model when compatibility needs to be verified |
| Carton Type | Provide the corrugated-board construction or total flap thickness when staple-leg selection is required |
| Quantity | Provide required coils, cartons, pallets or purchasing volume |
Send Your RR1-5/8 Requirements
RR1-5/8 is a roll carton-closing staple format with a 1-1/4-inch crown and 5/8-inch leg. It is used in compatible RR-type carton stapling systems.
The current KYA page identifies the product code as KYA-RR1-5/8.
The current KYA specification lists a 1-1/4-inch / 31.75mm crown.
The featured RR1-5/8 product uses a 5/8-inch nominal leg. KYA also publishes 15mm in the current product table.
The current KYA page specifies steel.
KYA currently lists copperized and galvanized surface finishes for the RR1-5/8 product.
The current product specification lists a chisel point.
The current KYA specification lists glue collation in a coil / roll format.
Current ISM and Spotnails RR1-family references define RR1-5/8 as 1,000 staples per roll. The KYA page also publishes a 5,000-piece roll option, so confirm whether that configuration should be ordered under an RR5 designation.
The current KYA table lists 24 coils per carton for the 1,000-piece coil format.
The current KYA table lists 6 coils per carton for the 5,000-piece coil format.
Current industry references distinguish RR1 and RR5 primarily by roll capacity: RR1 references use 1,000-staple rolls, while RR5 references use 5,000-staple rolls. Confirm KYA's current designation when specifying the larger coil.
No. RR1-5/8 uses a 1-1/4-inch crown, while SWC7437-type carton roll staples are commonly specified with a 1-3/8-inch crown. They require the appropriate carton-stapler system.
KYA currently references ISM RA1000T 5/8 and RA1000T 3/4 systems, while current ISM RR1-5/8 data confirms the same nominal 1-1/4-inch crown and 5/8-inch leg class. Verify the exact stapler model and current KYA coil dimensions before production use.
Spotnails specifies KSR3219R for its own 1-1/4-inch crown CCRR / RR-type carton staples from 5/8" to 3/4". This is a useful RR-system cross-reference, but the actual KYA staple and tool feed geometry should be confirmed before substitution.
Current KYA sources are not consistent enough to publish one verified gauge value for this exact product. Use crown, leg, coil format and full fastener dimensions for tool matching until the production drawing confirms the gauge.
The current page lists copperized and galvanized finishes but does not publish a specific outdoor exposure class, zinc thickness or corrosion-test rating. Select the finish according to the actual packaging and storage environment.
Their primary application is closing corrugated shipping and packaging cartons with a compatible roll carton stapler.
Provide the current staple reference, carton stapler manufacturer and model, 1-1/4-inch crown requirement, leg length and required roll capacity. Do not rely only on the words “coil carton staple.”
KYA supplies roll carton staples for packaging distributors, carton-closing equipment distributors, corrugated-box manufacturers, warehouses and industrial packaging operations.
For quotations on RR1-5/8 coil carton staples, provide the required finish, roll capacity, current staple reference, exact carton-stapler model, carton construction and purchasing quantity.
