KYA 15 Degree Ring Shank Coil Nails are wire-collated fasteners for fencing, sheathing, pallet and related wood-fastening applications. The featured model on this page is 2-1/4" × .099", approximately 57mm × 2.5mm, with a ring-shank configuration and 15-degree wire-coil collation.
The current KYA page describes this product family with a full round head and lists Q195/Q235 steel together with bright, electro-galvanized, hot-dip galvanized, mechanically galvanized and stainless-steel finish options. The exact finish should be specified when ordering because corrosion requirements differ between interior fencing components, protected construction and exterior exposure.
For nailer matching, verify the complete fastener specification: 15° wire collation, 2-1/4" length, .099" shank diameter, ring shank, head geometry and selected finish. Do not assume compatibility with every coil nailer from angle alone.
| Specification | Current Page Data |
|---|---|
| Featured Model | 2-1/4" × .099" |
| Nominal Length | 2-1/4" / approximately 57mm |
| Nominal Shank Diameter | .099" / approximately 2.5mm |
| Featured Shank Type | Ring Shank |
| Collation Angle | 15 Degree |
| Collation Type | Wire Coil |
| Head | Full Round Head according to the current product introduction |
| Steel Reference | Q195 / Q235 steel listed on the current page |
| .099" Family Length Range | 1-1/2"–2-1/2" / 38–64mm |
| .099" Family Coil Count | 300–350 nails per roll depending on configuration |
| Family Finish Options | Bright, Yellow Painted, Electro-Galvanized, Hot-Dip Galvanized, Mechanically Galvanized and Stainless Steel |
| Stainless Grades Listed | 304 and 316 within the broader product family |
| Primary Page Applications | Fencing, sheathing and pallet / crate manufacturing |
Specification scope: 2-1/4" × .099" is the exact model displayed for this URL. Broader length, diameter, head, shank and finish ranges on the current KYA page describe the complete coil-nail family and should not automatically be treated as attributes of this single SKU.
Request 2-1/4 x .099 Coil Nail Pricing
A ring shank uses annular ridges around the nail body. In suitable wood applications, this geometry is used where greater withdrawal resistance than a comparable smooth-shank fastener is required.
Actual fastening performance depends on wood species, moisture, density, nail dimensions, penetration, finish and joint design. The current KYA page does not publish a quantified withdrawal-strength value for this 2-1/4" × .099" model.
| Shank | Current KYA Family Description | Selection Guidance |
|---|---|---|
| Ring Shank | Featured shank type for this fencing-focused product page | Used where increased resistance to nail withdrawal is required in suitable wood |
| Smooth Shank | Listed in the broader coil-nail family | Common general-purpose option; not the featured shank on this URL |
| Screw Shank | Listed in the broader coil-nail family | Separate helical-shank configuration; do not treat it as identical to the ring-shank SKU |
The featured nails use 15-degree wire-coil collation. Welded wires hold the nails in a coil for feeding through a compatible pneumatic coil nailer.
A “15-degree coil nailer” description alone is not enough to establish compatibility. Confirm the tool's accepted collation material, nail length, shank diameter, head diameter and coil capacity before ordering.
The current KYA page describes the nails for use with 15-degree pneumatic wire-coil framing nailers. Current professional competitor systems demonstrate why the full dimensional range must still be checked.
| Tool / System Reference | Published Fastener Range | Matching Guidance |
|---|---|---|
| KYA Featured Nail | 2-1/4" × .099", ring shank, 15° wire coil | Primary fastener specification for this URL |
| SENCO SCN60XP | Current SENCO data lists 15° wire-collated ring-shank coil nails from 2" to 2-3/8" | Useful industry reference; confirm diameter, head and exact fastener specification before cross-brand use |
| Metabo HPT NV65AH2 | Current tool data accepts 15° wire coil nails from 1-1/2" to 2-1/4", approximately .090"–.099" | The featured KYA dimensions fall within this published dimensional class, but direct KYA compatibility should not be assumed without checking head and feed geometry |
| Other Coil Nailers | Varies by manufacturer and model | Verify 15° wire collation, 2-1/4" length, .099" diameter, head size and ring-shank acceptance |
Finish selection matters for fencing because exposure conditions can vary from protected indoor fabrication to exterior weather exposure. The current KYA family data lists several finish options, but the page does not bind one finish to every 2-1/4" × .099" order.
| Finish | Current Page Information | Use Consideration |
|---|---|---|
| Bright | Current page specifically describes bright finish for interior use in non-treated lumber | Do not position bright nails as general exterior fencing fasteners |
| Electro-Galvanized | Listed as a family finish option | Provides zinc coating, but the current page does not publish coating thickness or exposure classification |
| Hot-Dip Galvanized | Listed as a family finish option | Relevant where a more corrosion-resistant galvanized option is required; confirm project and lumber requirements |
| Mechanically Galvanized | Listed in the current family table | Confirm exact coating specification when required |
| Stainless Steel | 304 and 316 are listed within the broader KYA family | Confirm exact grade, size and availability for the required 2-1/4" × .099" configuration |
The current page does not publish zinc coating weight, salt-spray hours or a specific treated-lumber approval for this 2-1/4" × .099" SKU. Select the finish according to the actual fence material, preservative treatment and exposure requirement.
The table below preserves the current KYA family-level size data. The featured model on this page is 2-1/4" × .099"; other rows are related coil-nail configurations rather than the exact SKU.
| Shank Diameter | Published Length Range | Pcs / Roll | Family Shank Options | Family Finish Options |
|---|---|---|---|---|
| .082" / 2.1mm | 1-1/4"–2" / 32–50mm | 350–400 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .090" / 2.3mm | 1-1/4"–2" / 32–50mm | 300–400 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .092" / 2.3mm | 1-1/4"–2-1/4" / 32–57mm | 300–400 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .099" / 2.5mm | 1-1/2"–2-1/2" / 38–64mm | 300–350 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .105" / 2.7mm | 1-3/4"–2-3/4" / 44–70mm | 225–250 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .113" / 2.87mm | 1-3/4"–3" / 44–76mm | 225–250 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .120" / 3.1mm | 2"–3-1/2" / 50–89mm | 200–250 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .131" / 3.33mm | 2-1/2"–3-1/2" / 64–89mm | 200 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .148" / 3.76mm | 2-1/2"–3-1/2" / 64–89mm | 150 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
| .150" / 3.8mm | 3"–3-1/2" / 76–89mm | 150 | Smooth / Ring / Screw | Bright / Painted / EG / HDG / MG / SS |
Length-range note: the current KYA overview states a broader family length range of 1"–4", while the detailed diameter matrix on this same page lists configurations up to 3-1/2". Confirm the current production specification if a length outside the detailed matrix is required.
Fencing is the primary application focus of this URL. Ring-shank coil nails can be used for suitable wood-fence components where the nail dimensions, penetration and finish meet the project requirements.
The current KYA page lists wall and roof sheathing among the family applications. Verify nail size, finish and the applicable fastening schedule for the sheathing system being installed.
Pallet and crate manufacturing are also listed on the current page. Select ring, smooth or screw shank according to the wood, joint design and required production specification.
The broader KYA application list includes timber and softer-pine framing. The exact structural fastening schedule, nail dimensions and finish should be determined by the relevant project specification rather than from the family description alone.
The current page additionally lists ply bracing, composition roofing, underlayments, fiber-cement board, cabinet frames and furniture frames. These are family-level application references; verify that the exact 2-1/4" × .099" ring-shank configuration and finish are appropriate for the specific installation before use.
| Selection Parameter | What to Confirm |
|---|---|
| Length | Featured model is 2-1/4" / approximately 57mm; verify sufficient penetration for the fence component and substrate |
| Shank Diameter | Featured model uses .099" / approximately 2.5mm |
| Shank Type | Ring shank is featured on this page; confirm whether the application requires ring, smooth or screw shank |
| Finish | Match Bright, EG, HDG, MG or Stainless Steel to the actual exposure and lumber treatment requirement |
| Collation | 15° wire coil |
| Head Geometry | Current page introduction identifies full round head; confirm tool acceptance |
| Coil Nailer | Verify accepted length, diameter, wire collation, head dimensions and coil capacity from the nailer specification |
| Treated Lumber | Confirm the fastener material / coating required by the lumber supplier and project specification; the current KYA page specifically limits Bright finish to untreated interior lumber |
| Ordering Information | Featured / Required Specification |
|---|---|
| Model | 2-1/4" × .099" |
| Length | 2-1/4" / approximately 57mm |
| Shank Diameter | .099" / approximately 2.5mm |
| Shank Type | Ring Shank |
| Collation | 15° Wire Coil |
| Finish | Specify Bright, EG, HDG, MG or required Stainless Steel option; confirm exact availability for this size |
| Nailer | Provide exact manufacturer and model when compatibility needs confirmation |
| Application | Specify fencing, sheathing, pallet / crate or other intended application |
| Wood / Substrate | Identify untreated, treated or other lumber when finish selection is important |
| Quantity | Provide required coils, cartons, pallets or purchasing volume |
Send Your Coil Nail Requirements
The featured KYA model is 2-1/4" × .099", approximately 57mm long with a 2.5mm nominal shank diameter.
Yes. Ring shank is the featured shank configuration on this fencing-focused product page.
The current KYA specification lists 15-degree wire-coil collation.
The current product introduction identifies a full round head for the featured ring-shank coil nail. The broader KYA family also lists other head styles, which should not be assumed for this exact configuration.
The current family table lists approximately 300–350 nails per roll for .099" diameter configurations, depending on length and configuration. The page does not provide one separate exact coil count for the 2-1/4" × .099" ring-shank SKU.
The current page lists Q195 / Q235 steel for the steel coil-nail family and also lists stainless-steel options in 304 and 316 grades.
The current KYA page specifically describes Bright finish as suitable for interior use in non-treated lumber. Do not position Bright finish as a general exterior fencing fastener.
Current KYA family data lists Bright, Yellow Painted, Electro-Galvanized, Hot-Dip Galvanized, Mechanically Galvanized and Stainless Steel options. Confirm the exact finish availability for the 2-1/4" × .099" ring-shank configuration.
The current page does not publish a specific treated-lumber approval for this SKU. Confirm the required fastener material or coating from the lumber supplier and applicable project specification before use.
Universal compatibility should not be assumed. The nailer must accept 15° wire-collated nails with the required 2-1/4" length, .099" diameter, head geometry and coil configuration.
Metabo HPT currently publishes the NV65AH2 for 15° wire coil nails from 1-1/2" to 2-1/4" and approximately .090"–.099", so the featured KYA dimensions fall within that published dimensional class. Direct cross-brand compatibility still requires confirmation of head and feed geometry.
SENCO currently publishes several 15° wire-coil tools that accept ring-shank fasteners, including 2-1/4" lengths. Confirm the exact SENCO tool's diameter, head and finish requirements before using another manufacturer's nail.
The current KYA page primarily positions them for fencing, sheathing and pallet / crate manufacturing, with additional family applications listed for other construction and woodworking uses.
Composition roofing appears in the broader KYA family application list, but this page does not establish the featured 2-1/4" × .099" fencing nail as a dedicated roofing nail. Use the fastener dimensions and roofing-system specification required for the actual installation.
Fiber-cement board appears in the broader KYA application list. Verify the board manufacturer's fastening requirements, nail dimensions, head geometry and corrosion specification before using the featured SKU.
Ring-shank geometry is used where increased resistance to withdrawal is required compared with a comparable smooth-shank nail in suitable wood. The current page does not publish a specific numerical holding-power increase.
Provide the existing nail size, shank type, finish, collation angle, collation material and exact coil-nailer model. For this page, the main reference is 2-1/4" × .099", ring shank and 15° wire collation.
Ask About Ring Shank Coil Nails
KYA supplies wire-collated coil nails for fastener distributors, fencing suppliers, pallet and crate manufacturers, woodworking suppliers and pneumatic-tool distributors.
For quotations on 2-1/4" × .099" 15° ring shank coil nails, provide the required finish, coil nailer model, application, lumber type and purchasing quantity so the exact configuration can be identified.
