| Length: | |
|---|---|
| Quantity: | |
KYA S05-14PH Polymer Composite Staples are 16 gauge non-metal fasteners with a 12.7mm / 1/2 inch crown and a 14mm / approximately 9/16 inch leg length. They are designed for industrial fastening applications where conventional metal staples may create corrosion, conductivity, metal-contamination or downstream machining concerns.
The S05-14PH uses polymer composite material with a smooth shank and an approximately 1.35mm staple width. Standard packing is 4,200 staples per box and 30 boxes per carton.
Typical applications include boatbuilding, fiberglass lay-up, composite manufacturing, lumber tagging, lumber wrap, radiant barrier installation, house wrap, casket lining, cabinetry and casegoods production.
| Specification | Details |
| Product | 16 Gauge Polymer Composite Staples |
| Model | S05-14PH |
| Gauge | 16 Gauge |
| Material | Polymer Composite |
| Crown Width | 12.7mm / 1/2 Inch |
| Leg Length | 14mm / Approx. 9/16 Inch |
| Staple Width | 1.35mm |
| Shank | Smooth |
| Fastener Type | Non-Metal Polymer Composite Staple |
| Electrical Property | Non-Conductive Polymer Composite |
| Staples per Box | 4,200 pcs |
| Boxes per Carton | 30 boxes |
| KYA Referenced Tool Systems | BeA 95/14-650, Spotnails 95/14-650, Fasco PS50-650 |
| Typical Applications | Boatbuilding, Fiberglass, Composites, Lumber, Insulation, House Wrap, Cabinetry and Casket Lining |
The S05-14PH is specifically the 14mm leg model. Other S05 Series staples are available in shorter lengths, but those dimensions should not be treated as the specification of the S05-14PH itself.
The S05-14PH uses a 12.7mm / 1/2 inch crown. This crown size is commonly used by industrial polymer-composite staple systems for lumber, composite manufacturing, marine construction and insulation applications.
Crown width must match the stapler magazine and driver. When replacing another manufacturer's composite fastener, confirm the actual crown, staple cross-section and leg length rather than selecting only by gauge.
The S05-14PH has a 14mm leg, approximately equivalent to 9/16 inch. This is the longest size shown in the KYA S05 Series table and is intended for applications requiring more penetration than the shorter 4mm, 6mm, 8mm or 9.5mm versions.
Final staple length should be selected according to substrate thickness, density, application load and the accepted fastener range of the stapler.
The S05-14PH is a heavier 16 gauge polymer composite staple. Compared with smaller polymer staples, the larger fastener cross-section is intended for applications requiring a more substantial non-metal fastening point.
Holding performance depends on the polymer grade, substrate, penetration depth and installation method. Production users should test the S05-14PH in the actual wood, composite, insulation or laminate system before high-volume use.
Because the staple body is polymer composite rather than steel, the fastener does not introduce a conventional metallic staple into the workpiece.
The polymer material is non-conductive, making these staples useful in applications where electrical conductivity from a metal fastener is undesirable. Electrical or safety-critical assemblies should still be evaluated according to the requirements of the complete installed system.
A polymer composite staple does not develop steel rust because the staple body is non-metal. This can help avoid rust staining associated with conventional carbon-steel fasteners.
Suitability for marine, wet, chemical or high-temperature environments still depends on the polymer grade, substrate, resin system and service conditions of the finished assembly.
Polymer composite staples are commonly selected where the fastened component may later be cut, sanded, routed, shaped or planed. The non-metal fastener can be processed together with compatible wood and composite materials.
Polymer fastener grades and cutting tools vary. Buyers using sensitive blades, router bits, sanding systems or high-speed machining equipment should validate the exact staple grade with the intended tooling before production.
The S05-14PH can be useful in manufacturing processes where introducing a metal staple into lumber, composites or finished components is undesirable.
For facilities using downstream metal-detection systems, validate the complete finished product with the actual detector sensitivity and production settings rather than relying only on the non-metal composition of the staple.
The S05 family uses a 12.7mm crown and 1.35mm listed width across several leg lengths. The S05-14PH is the 14mm version with 4,200 staples per box.
| Model | Crown | Width | Leg Length | Pcs/Box | Boxes/Carton |
|---|---|---|---|---|---|
| S05-14PH | 12.7mm | 1.35mm | 14mm | 4,200 | 30 |
| S05-10PH | 12.7mm | 1.35mm | 9.5mm | 5,040 | 32 |
| S05-04 | 12.7mm | 1.35mm | 4mm | 5,040 | 40 |
| S05-06 | 12.7mm | 1.35mm | 6mm | 5,040 | 40 |
| S05-08 | 12.7mm | 1.35mm | 8mm | 5,040 | 40 |
| S05-10 | 12.7mm | 1.35mm | 9.5mm | 5,040 | 40 |
| S05-14 | 12.7mm | 1.35mm | 14mm | 5,040 | 40 |
S05-14PH and S05-14 share the same listed 14mm length but have different standard packaging. Buyers should specify the exact model suffix rather than ordering only by length.
KYA references BeA 95/14-650, Spotnails 95/14-650 and Fasco PS50-650 systems for the S05-14PH product range.
Compatibility should be checked by the exact tool model, 16 gauge fastener specification, 12.7mm crown, staple cross-section and 14mm leg length. Similar polymer staple guns may use different crowns or magazine geometries.
| Tool Reference | Compatibility Check |
|---|---|
| KYA Referenced BeA System | Confirm exact model, 1/2-inch crown, 16 gauge specification and 14mm maximum length. |
| KYA Referenced Spotnails System | Confirm actual tool model and polymer staple magazine specification. |
| KYA Referenced Fasco System | Confirm exact fastener dimensions and accepted polymer composite staple format. |
| Other 16GA Polymer Staplers | Do not assume compatibility from gauge alone; confirm crown, leg length and cross-section. |
Current industry tools are available for 16 gauge, 1/2-inch crown polymer composite staples up to approximately 14mm / 9/16 inch. Provide the exact stapler model when requesting replacement fasteners.
The 14mm S05-14PH is designed for professional non-metal fastening in woodworking, marine, composite and insulation applications where a longer polymer staple is required.
Boatbuilding
Fiberglass lay-up
Composite manufacturing
Lumber tagging
Lumber wrap
Radiant barrier installation
House wrap
Casket lining
Casegoods and cabinetry
Woodworking and millwork
Cable and wire positioning where permitted by the installation specification
Polymer composite staples are used in selected boatbuilding and fiberglass lay-up processes where leaving conventional metal fasteners in the laminate is undesirable.
The 14mm leg provides deeper penetration than shorter S05 Series staples, but suitability depends on the laminate, core material, resin system and production method. Test the actual staple in the intended composite process before volume use.
Non-metal staples are useful for lumber wrap, tags and temporary fastening where timber may later pass through saws, moulders, routers or sanding equipment.
Machining compatibility depends on both fastener grade and cutting equipment. Confirm the staple material grade when downstream blade protection is a critical production requirement.
S05 Series polymer staples can be used for selected radiant barrier, house-wrap and insulation fastening applications where the crown and leg length match the membrane, substrate and installation method.
Follow the membrane or insulation manufacturer's fastening requirements for staple spacing, penetration depth and substrate compatibility.
| Buyer Check | S05-14PH Reference |
|---|---|
| Model | S05-14PH |
| Gauge | 16 Gauge |
| Crown | 12.7mm / 1/2 Inch |
| Leg Length | 14mm / Approx. 9/16 Inch |
| Staple Width | 1.35mm |
| Material | Polymer Composite |
| Stapler | Confirm exact 16GA polymer staple tool and magazine dimensions. |
| Substrate | Test holding performance in the actual wood, laminate, composite or insulation system. |
| Post-Processing | Confirm compatibility with intended cutting, sanding, routing or planing process. |
The S05-14PH is packed at 4,200 staples per box and 30 boxes per carton. This packaging format is suitable for boat builders, composite manufacturers, woodworking factories, insulation contractors, fastener distributors and other production users.
| Packing Item | S05-14PH |
| Staples per Box | 4,200 pcs |
| Boxes per Carton | 30 boxes |
| Staple Length | 14mm |
| Crown | 12.7mm |
KYA supplies polymer composite staples for boat builders, composite manufacturers, timber processors, cabinet manufacturers, insulation contractors and fastener distributors.
Custom color, staple length and packaging requirements can be discussed for bulk purchasing. Provide the exact stapler model, required fastener dimensions, application and purchasing quantity when requesting a quotation.
KYA supplies multiple polymer composite staple sizes for professional non-metal fastening applications, including 16 gauge and 19 gauge product families with different crowns and leg lengths.
The S05-14PH is a 16 gauge polymer composite staple with a 12.7mm / 1/2 inch crown, 1.35mm listed width and 14mm leg length.
Yes. The S05-14PH model itself has a 14mm leg. Shorter lengths belong to other S05 Series models.
Yes. A 14mm staple leg is approximately equivalent to 9/16 inch.
They are made from non-metal polymer composite material.
The polymer composite fastener is non-conductive. For safety-critical electrical applications, verify the complete installed system against the applicable requirements.
The polymer staple itself does not develop steel rust because it does not use a conventional steel staple body.
Polymer composite staples are commonly designed to be sawed, sanded and planed with compatible workpieces. Tool compatibility should still be tested with the actual polymer grade and machining equipment.
Polymer fasteners are selected specifically to reduce the problems associated with striking metal fasteners during machining. However, polymer grades and cutting tools vary, so sensitive tooling should be tested with the actual fastener before production.
Polymer composite fasteners are designed to provide mechanical holding in compatible substrates, and some polymer systems can develop additional adhesion during driving. Actual joint strength depends on the fastener material, substrate and production conditions and should be tested for the intended application.
Fiberglass lay-up and composite manufacturing are among the listed applications. Test the fastener with the actual laminate, core and resin system before production use.
Yes. Boatbuilding is a common application for polymer composite fasteners where leaving a conventional metal staple in the workpiece is undesirable.
Yes. Lumber tagging and lumber wrap are common industrial applications for non-metal polymer composite staples.
Yes, where a 14mm staple is appropriate for the membrane and substrate. Follow the insulation or membrane manufacturer's fastening requirements.
KYA references BeA 95/14-650, Spotnails 95/14-650 and Fasco PS50-650 systems. Because tool model designations can vary by market, confirm the exact stapler and fastener dimensions before ordering.
No. The stapler must be designed for compatible 16 gauge polymer composite staples with a 12.7mm / 1/2 inch crown and 14mm leg length.
The S05-14PH is packed at 4,200 staples per box.
The listed packaging is 30 boxes per carton for the S05-14PH model.
Both are listed with a 14mm leg, 12.7mm crown and 1.35mm width, but the standard packaging differs. S05-14PH is listed at 4,200 pcs/box and 30 boxes/carton, while S05-14 is listed at 5,040 pcs/box and 40 boxes/carton. Confirm the exact model suffix before ordering.
Custom color, staple length and packaging requirements can be discussed for bulk orders. Provide the application, stapler model, required dimensions and purchasing quantity when requesting a quotation.
