KYA 24/6 Office Staples are zinc-plated steel staples for office stapling applications. This specific 24/6 model has a 12.85mm crown, 6.0mm leg length, 0.50mm width and 0.45mm thickness, with a chisel point.
The specifications below apply specifically to the KYA 24/6 model shown on this page. Other office staple sizes or products in the KYA office staple range may use different dimensions and should be checked separately.
Use the dimensional information in this table when checking whether these staples match your stapler requirements. Do not rely on the 24/6 designation alone when a stapler manufacturer provides additional dimensional requirements.
| Attribute | 24/6 Model Specification |
| Staple Size | 24/6 |
| Crown | 12.85mm |
| Width | 0.50mm |
| Thickness | 0.45mm |
| Leg Length | 6.0mm |
| Material | Steel |
| Surface Finish | Zinc Plated |
| Point Type | Chisel Point |
These are the specifications listed for this KYA 24/6 product. They should not be treated as specifications for every 24/6 staple from other manufacturers or for other KYA office staple sizes.
The original KYA product information lists Rexel, Rapid, Leitz, Novus and Esselte as brand references for these 24/6 office staples. This should not be interpreted as confirmation that every stapler made by these brands accepts this staple.
Before ordering, check the staple specification printed on the stapler, its packaging or the stapler manufacturer's documentation. If the stapler specifies 24/6 staples, compare its requirements with the KYA model dimensions shown above.
Compatibility with an individual stapler model has not been stated here unless it is specifically identified by the product information. If you are uncertain about a particular stapler, provide its brand and model when contacting KYA.
This KYA 24/6 model is made from steel with a zinc-plated surface finish. The product specification identifies the point geometry as a chisel point.
The terms “steel,” “zinc plated” and “chisel point” describe the material, surface finish and point type of this product. No additional corrosion rating, coating performance level or penetration rating is stated on this page.
The KYA product information identifies these 24/6 staples for common office stapling tasks involving paper documents and similar stationery materials.
Documents and reports
Notebooks and diaries
Calendars
Office memos and presentations
The number of sheets that can be stapled should be determined from the stapler manufacturer's specification rather than assumed from the staple size alone.
First, check whether your stapler identifies 24/6 as an accepted staple size. Then compare any dimensional information supplied by the stapler manufacturer with this KYA model: 12.85mm crown, 6.0mm leg length, 0.50mm width and 0.45mm thickness.
Do not assume compatibility solely because the stapler and staples are intended for office use or because a brand produces other staplers that accept 24/6 staples. Compatibility should be checked against the specific stapler model.
This model has a 12.85mm crown, 6.0mm leg length, 0.50mm width and 0.45mm thickness.
The product specification lists steel as the material and zinc plated as the surface finish.
The KYA 24/6 model uses a chisel point. This describes the point geometry specified for the staple.
The original KYA product information lists Rexel, Rapid, Leitz, Novus and Esselte as brand references. This does not mean every stapler from those brands accepts this staple. Check that the specific stapler model specifies 24/6 staples before ordering.
This page only defines the dimensions of the KYA model shown here. For purchasing and compatibility decisions, use the listed KYA dimensions together with the requirements of the specific stapler rather than assuming that every product carrying a 24/6 designation is dimensionally identical.
A sheet-capacity rating is not specified for this KYA staple on this page. Stapling capacity depends on the stapler and the material being stapled, so refer to the specification of the specific stapler being used.
Check the accepted staple size in your stapler documentation and compare it with this product's 24/6 designation and listed dimensions. If additional confirmation is required, provide KYA with the stapler brand and model when making an inquiry.
