| Material: | |
|---|---|
| Surface Treatment: | |
| Quantity: | |
KYA 15 Degree Plastic Sheet Concrete Steel Nails in 2.6mm × 30mm are electro-galvanized high-carbon steel fasteners designed for compatible direct-fastening and concrete-nailing systems.
The featured SKU uses a 2.6mm / .102 inch smooth shank, 30mm / approximately 1.18 inch length, 5.2mm head diameter, diamond point and 15° plastic sheet collation. Each coil contains 300 nails, with 40 coils per carton.
Typical applications include fastening suitable furring strips, drywall track, clips, light-gauge components and other non-structural materials to compatible concrete or masonry substrates. Actual suitability depends on base-material strength, attached-material thickness, required embedment and the concrete nailer's approved fastener specification.
| Specification | Details |
|---|---|
| Model | 2.6 × 30mm |
| KYA Code | KYA-2.6X30SM |
| Product Type | Plastic Sheet Collated Concrete Steel Nail |
| Shank Diameter | 2.6mm / .102 in. |
| Nail Length | 30mm / approximately 1.18 in. |
| Head Diameter | 5.2mm |
| Shank Type | Smooth Shank |
| Point Type | Diamond Point |
| Head Type | Full Round Head |
| Collation | Plastic Sheet |
| Collation Angle | 15° |
| Material | #45 High-Carbon Steel |
| Finish | Electro-Galvanized |
| Nails per Coil | 300 pcs |
| Coils per Carton | 40 coils |
| Tool Requirement | Concrete nailer specifically rated for 2.6 × 30mm, 15° plastic-collated concrete nails |
Important: do not select a nailer based only on the 15° angle. The tool must also accept the 2.6mm shank diameter, 30mm length, 5.2mm head, plastic-sheet collation and complete coil geometry.
Request 2.6x30mm Nail PricingThe product uses #45 high-carbon steel with a nominal 2.6mm shank diameter. Concrete-fastening performance depends not only on steel material but also on heat treatment, nail geometry, base material and driving energy, so application-specific testing is recommended.
The 30mm length provides a compact concrete-fastening option for suitable light attachments. Select the nail according to the thickness of the material being fastened and the required penetration into the receiving substrate.
The smooth shank is designed for direct driving into compatible substrates. Final holding performance depends on substrate density, embedment depth and fastener geometry rather than shank type alone.
The diamond point concentrates driving force at the nail tip to support entry into compatible base materials. Concrete strength, aggregate and tool power still determine whether the fastening is suitable.
The 5.2mm head provides the bearing surface for the attached component. Head diameter is also an important tool-compatibility parameter because the driver, nose and magazine must accommodate the complete fastener profile.
The plastic carrier holds the nails in a 15° coil for automatic feeding through a compatible tool. During driving, the individual nail separates from the collation material. The exact plastic-sheet format and coil geometry must match the nailer magazine.
The current KYA specification lists 300 nails per coil and 40 coils per carton, supporting repetitive fastening in compatible production and construction applications.
The 30mm concrete nail can be considered for attaching suitable thin furring components where the material thickness and required embedment are compatible with the fastener and approved nailer.
Light-gauge drywall track and similar metal components can be fastened to suitable concrete with an approved direct-fastening system using the correct nail dimensions and driving energy.
Concrete nails are commonly used with selected electrical clips, conduit clips, clamps and lightweight fixtures where the attachment and substrate are suitable for direct fastening.
The fastener may be considered for selected temporary or non-structural construction work when the tool system, substrate and required holding performance have been verified.
Thin metal tracks or accessories can be attached to compatible concrete or masonry substrates where the complete fastening system is approved for the material combination.
| Feature | Concrete Steel Nail | General Coil Nail |
|---|---|---|
| Primary Use | Direct fastening into compatible concrete, masonry or other approved hard substrates | Wood, pallets, siding, sheathing, fencing and other wood fastening |
| Material Requirement | Steel and treatment suitable for direct-fastening loads | Varies according to wood-fastening application |
| Tool | Approved concrete / direct-fastening nailer | General coil nailer |
| Interchangeable? | No. Do not select only by angle, nail length or coil appearance. | |
Electro-galvanizing provides a zinc coating that offers basic corrosion protection compared with untreated steel. It is commonly suitable for dry interior or limited-exposure applications.
For permanently wet, exterior, chemically aggressive or coastal environments, confirm whether a different coating or stainless steel fastener is required. Electro-galvanized should not automatically be treated as equivalent to hot-dip galvanized or stainless steel.
| Selection Factor | What to Check |
|---|---|
| Attached Material Thickness | Thickness of track, wood strip, clip or other component |
| Required Embedment | Required penetration into the receiving base material |
| Base Material | Concrete, masonry, block, steel or other approved material |
| Concrete Strength | Concrete density and aggregate affect driveability and holding performance |
| Edge Distance | Avoid fastening too close to edges where cracking may occur |
| Tool Capacity | The nailer must be approved for the exact fastener geometry |
Not all concrete behaves the same during direct fastening. Concrete compressive strength, aggregate hardness, age, surface condition and edge distance can affect nail penetration, bending, breakage and holding performance.
Before repetitive installation, perform trial fastenings using the actual nailer, fastener and substrate. Applications requiring defined structural loads should use documented engineering or load-test data rather than generic product claims.
A compatible tool must match the entire fastener specification. A conventional 15° pallet, siding, roofing or framing coil nailer should not automatically be treated as compatible with this concrete steel nail.
| Compatibility Parameter | KYA 2.6x30mm Requirement |
|---|---|
| Shank Diameter | 2.6mm / .102 in. |
| Nail Length | 30mm |
| Head Diameter | 5.2mm |
| Collation Angle | 15° |
| Collation Material | Plastic Sheet |
| Coil Capacity | 300 nails |
| Tool Type | Concrete / direct-fastening nailer explicitly approved for this fastener configuration |
If replacing an existing fastener, provide the exact nailer manufacturer, tool model, current fastener code and physical dimensions to KYA before placing a bulk order.
The wider KYA coil nail range includes several point geometries. This specific 2.6×30mm product is listed with a diamond point. Alternative point types shown in family diagrams should not automatically be treated as specifications of this SKU.
KYA manufactures coil fasteners with smooth, screw and ring shanks across different product families. The product described on this page is specifically a smooth-shank concrete steel nail. Do not substitute a different shank profile without confirming the application and tool specification.
| Ordering Information | Required Detail |
|---|---|
| Size | 2.6mm × 30mm |
| Head Diameter | 5.2mm |
| Shank | Smooth |
| Point | Diamond |
| Finish | Electro-Galvanized |
| Collation | 15° Plastic Sheet |
| Nailer Model | Provide exact tool manufacturer and model |
| Base Material | Concrete, masonry or other approved substrate |
| Attached Material | Track, furring strip, clip, bracket or other component |
| Quantity | Coils, cartons, pallets or annual volume |
The featured SKU has a 2.6mm shank diameter and 30mm nail length, with a 5.2mm head diameter.
KYA lists #45 high-carbon steel with an electro-galvanized surface finish for this product.
This 2.6×30mm product uses a smooth shank.
The current KYA specification lists a diamond point.
The current specification lists 300 nails per coil.
KYA currently lists 40 coils per carton for this configuration.
The nails are connected by a plastic carrier in a 15° coil arrangement for automatic feeding through a compatible nailer. The tool must be designed for the same collation and fastener dimensions.
They can be considered for suitable furring-strip fastening where the strip thickness, substrate, required embedment and approved tool system match the 30mm fastener length.
Yes, light-gauge drywall track to suitable concrete is a relevant application for direct-fastening nails when the nailer and fastener system are approved for the substrate.
The existing KYA page previously made a 2mm steel penetration claim, but the supplied product data does not include the test conditions required to verify that value. Confirm steel thickness, steel grade, tool energy and application-specific test data before using the fastener for steel penetration.
Electro-galvanized fasteners provide basic zinc corrosion protection but are generally more appropriate for dry or limited-exposure conditions. For long-term wet, coastal or aggressive exposure, confirm a more corrosion-resistant specification.
Do not assume compatibility. Tool selection must be based on the exact manufacturer's fastener specification. The 2.6mm diameter and plastic-sheet collation of this product must match the specific nailer before use.
No. A 15° angle alone does not establish compatibility. Diameter, length, head size, collation material and coil geometry must also match.
Consider the thickness of the attached material, required embedment, concrete strength, edge distance and the nail lengths approved for the tool. Longer is not automatically better for harder concrete.
Contact KYA regarding current sample availability. Test the exact fastener with the intended nailer, attached material and base material before high-volume production use.
KYA supplies concrete and direct-fastening nails for fastener distributors, construction suppliers, drywall-system suppliers, tool distributors and professional fastening users.
For quotations on 2.6×30mm 15° electro-galvanized plastic-sheet concrete steel nails, provide the exact nailer model, base material, attached material, quantity, packaging and destination market.
Request a Bulk Quote View More Plastic Sheet Nails
