KYA-400B Automatic Rebar Tier Tying Machine
The KYA-400B rebar tying tool is lightweight and has a compact, easy to hold grip. The tool is well balanced and is designed to tie rebars as fast as you can pull the trigger. Included with the tool are two lithium-ion batteries. The tool comes with three spools of 21 gauge tie wire.
● Lightweight and compact body.
● Li-Ion higher capacity battery.
● Brushless twisting motor.
● Reduced tying time.
● Reduce the risk of health problems.
● Simple one-handed operation.
Similar Tool:MAX RB398 Rebar Tier, MAX RB397 Rebar Tier, etc.
|No||Normal||Common faults||Warning voice||Possible reason||Inspecting items||Solution|
|1||Power ON→ The Tip |
Axis is initialized
and the wire-cutter
|No operation takes |
|No sound emitted||Battery completely empty||Confirm the battery is charged.||Perform normal charge.|
|Electrode plate has been oxidized||Take out the battery and see if the |
electrode has been brown.
|Polish terminal part of battery pack with dry cloth, etc|
|Continuous short beeps(Pi,pi,pi…)||Curl guide is open||Open/close curl guide.||Fully close curl guide.|
|Binding wire has been entangled around Twist section.||Turn off power and take out the battery to confirm if binding wire has been entangled inside curl guide.||Turn off power, remove binding wire inside curl guide|
|Two long beeps||Battery Is empty||Confirm the battery is charged||Perform normal charge|
|2||Trigger ON→ |
Wire is sent out.
|No wire is sent out||Continuous short||Curl guide is open||Open/close curl guide||Fully close curl guide|
|Three short beeps |
|Tie-wire has been run out||Check if the Tie-wire has been run||Set the new tie wire|
|Wire caught inside reel||Check if wire inside reel has been loosened and caught||Remove fray on reel|
|Cutter section is blocked with foreign substance||Confirm functioning of Cutter section||Either wipe Cutter section with dry cloth or blow it with air|
|A wire is caught in the cutter section or Wire guide A||Check if any wire is caught.||Diassemble the cutter section and remove the caught wire|
|3||Binding wire draws a circle.||Curl is disordered and steps out of curl||No sound emitted||Wire, by hitting reinforcing bars, was repelled||check if wire hits reinforcing bars at binding||Pay attention so that wire does not hit reinforcing bars at binding|
|4||Wire is subject to |
|No wire cutting takes |
|No sound emitted||Cutter section is blocked with foreign |
|Confirm function of Cutter section.||Either wipe Cutter section with dry cloth or blow it with air|
|5||Wire twisting |
|Wire gets |
|No sound emitted||Wire, by hitting reinforcing bars,was repelled||Check if wire hits reinforcing bars at binding||Pay attention so that wire does not hit reinforcing bars at binding.|
|Binding power is week||No sound emitted||Reinforcing bars is not of designated size.||Confirm size of reinforcing bars to be bound||Use approriate diameter scope|
|Erroneous handling such as improper application of machine||Confirm how to apply machine to reinforcing bars||Adjust the Torque to a higher lever and insert in vertical direction. Use as tilting at45°|
|Twisting-off takes |
|No sound emitted||Reinforcing bars is not of |
|Confirm size of reinforcing bars to be bound||Use approriate diameter scope|
|Erroneous handling such as improper application of machine||Confirm how to apply machine to reinforcing |
|Adjust the Torque to a lower lever and insert in vertical direction. Use as tilting at45°|
|Works properly||Two long beeps repeated(Pi-pi, pi-pi,...)||Low power remains in the battery pack||Confirm the battery is fully charged.||Perform normal charge|
|Four short beeps repeated(Pipipipi, |
|The tool is used at high temperature.||Check the temperature at the job site.||Leave the tool and the battery pack at normal temperature in the room for some time. and then continue the operation.|