| Material: | |
|---|---|
| Surface Treatment: | |
| Quantity: | |
KYA 15 Degree Galvanized Plastic Sheet Coil Nails in 1.80mm × 19mm / 0.071" × 3/4" feature a ring shank, galvanized steel construction and plastic-sheet collation for use with compatible coil nailing systems.
The ring shank increases resistance to nail back-out compared with a smooth shank in suitable wood substrates, while the 15° plastic sheet collation keeps the fasteners organized for rapid sequential feeding through compatible coil nailers.
This compact 1.8 × 19mm ring shank coil nail is intended for applications where the short 19mm leg length and 1.8mm shank match the material thickness and required penetration. Always verify the complete nail specification and nailer fastener range before production use.
| Specification | Details |
|---|---|
| Product Type | Plastic Sheet Collated Coil Nail |
| Product Code | KYA-1.8X19R |
| Shank Diameter | 1.80mm / 0.071 in. |
| Nail Length | 19mm / 3/4 in. |
| Shank Type | Ring Shank |
| Collation | Plastic Sheet |
| Collation Angle | 15° |
| Main Material | Steel |
| Finish | Galvanized |
| Head Type | Full Round Head |
| Compatible Tool Type | Compatible Plastic-Sheet Coil Nailers Rated for This Fastener Size |
| Coil Capacity | Varies by production and collation configuration; confirm exact coil count when ordering |
Important: 1.80 × 19mm is the specification for this SKU. Broader KYA plastic-sheet coil nail families are available in other diameters and lengths, but those family ranges should not be interpreted as the dimensions of this specific nail.
Request 1.8x19mm Coil Nail PricingThe annular rings along the shank increase friction with surrounding wood fibers after driving, helping the nail resist backing out in suitable timber and wood-based substrates.
Plastic-sheet collation holds the nails in a coil for automatic feeding through a compatible nailer. The 15° format should be matched to the magazine angle and fastener specification specified by the tool manufacturer.
At only 19mm / 3/4 inch long, this nail is intended for thinner fastening assemblies where longer siding, fencing or framing nails would provide excessive penetration. Confirm the actual workpiece and receiving substrate before selection.
The 1.80mm / 0.071-inch shank is significantly finer than common heavy framing, fencing or roofing coil nails. Tool compatibility should therefore be checked by exact fastener dimensions rather than by the term “15-degree coil nail” alone.
The galvanized coating provides corrosion protection compared with uncoated bright steel. The suitability of the coating for outdoor, humid, treated-lumber or corrosive environments depends on the exact galvanizing process and project requirements.
Plastic sheet coil nails are collated fasteners held together by a flexible plastic carrier so multiple nails can be loaded into a coil nailer. During driving, each nail separates from the collation material as it leaves the tool.
The main purchasing advantage is not simply the plastic material itself. Buyers should compare nail diameter, length, head diameter, shank profile, collation angle, coil direction, coil count and nailer compatibility.
| Shank Type | Characteristic | General Selection |
|---|---|---|
| Ring Shank | Annular rings increase friction and resistance to pull-out | Applications where increased holding performance is required |
| Smooth Shank | Smooth cylindrical surface for easier driving | General fastening where maximum withdrawal resistance is not required |
| Screw Shank | Twisted profile rotates as it enters suitable wood | Selected hardwood and industrial fastening applications |
The short 19mm length can be considered for selected thin siding, trim or accessory fastening where the substrate and installation specification permit this nail diameter and penetration depth.
The 1.8mm × 19mm format may be used in suitable light wood and panel assemblies where a compact ring-shank fastener provides sufficient penetration and holding performance.
Selected packaging, light crate and industrial wood-product applications can use short plastic-collated coil nails where material thickness and nailer specifications match.
The compact fastener size can also suit OEM manufacturing applications that require a 1.80mm ring-shank nail and 19mm leg length. Buyers should provide the existing tool or fastener drawing when replacing another product.
Not every product sold as a siding coil nail has the same dimensions. The 1.80 × 19mm nail on this page is much shorter and finer than many common siding coil nails, so buyers should avoid selecting it only by application name.
| Parameter | KYA 1.80x19mm | Typical Larger Siding Nail |
|---|---|---|
| Shank Diameter | 1.80mm / 0.071 in. | Often larger; verify project specification |
| Length | 19mm / 3/4 in. | Often substantially longer |
| Shank | Ring Shank | Ring or Smooth |
| Collation | 15° Plastic Sheet | 15° Wire or Plastic Sheet depending on system |
| Selection Method | Match the exact material, required penetration and nailer specification rather than using the term “siding nail” alone. | |
| Finish | General Characteristics | Typical Selection |
|---|---|---|
| Electro / Standard Galvanized | Zinc coating provides basic corrosion protection | Interior, sheltered or lower-exposure applications depending on coating specification |
| Hot-Dip Galvanized | Generally heavier zinc coating | Applications requiring higher corrosion protection where HDG is specified |
| 304 / 316 Stainless Steel | Higher corrosion resistance than standard carbon-steel galvanized fasteners | Wet, coastal, marine or other demanding environments according to project specification |
Do not determine exterior suitability from the word “galvanized” alone. Confirm the coating type, exposure environment, substrate and applicable project requirements before ordering.
A nailer must support more than just a 15-degree angle. Before replacing an existing fastener, compare the following specifications.
| Compatibility Factor | This Product |
|---|---|
| Collation Angle | 15° |
| Collation Type | Plastic Sheet |
| Shank Diameter | 1.80mm / 0.071 in. |
| Nail Length | 19mm / 3/4 in. |
| Shank Type | Ring Shank |
| Head | Full Round Head |
| Coil / Magazine Geometry | Confirm against exact nailer model |
Do not assume that every 15° coil nailer can feed a 1.80 × 19mm plastic-sheet nail. Many 15° framing, roofing and siding nailers are designed for significantly larger fasteners.
| Purchasing Information | Required Detail |
|---|---|
| Size | 1.80mm × 19mm |
| Collation | 15° Plastic Sheet |
| Shank | Ring Shank |
| Finish | Specify required galvanized coating or alternative finish |
| Nailer Model | Provide exact tool model when compatibility confirmation is required |
| Application | Provide material type and thickness |
| Quantity | Coils, cartons, pallets or annual volume |
| Packaging | Standard export packing or OEM/private-label requirements |
The featured size is 1.80mm shank diameter × 19mm length, approximately 0.071 inch × 3/4 inch.
This product uses a 15-degree plastic-sheet collation.
The annular ring profile increases friction between the nail and surrounding wood fibers, helping improve withdrawal resistance compared with a comparable smooth shank in suitable wood.
A 19mm nail is considerably shorter than typical framing fasteners. Do not use this product for structural framing unless the specific fastening system and project specification explicitly call for this size.
They can be considered for selected thin siding, trim or accessory fastening applications when 19mm penetration and a 1.80mm shank meet the installation requirement. Many conventional siding applications use larger and longer nails, so confirm the system specification first.
Yes. The product on this page is specified as galvanized steel. Confirm the exact coating type when corrosion performance is critical.
KYA's wider plastic-sheet coil nail family includes hot-dip galvanized and stainless steel options. Confirm availability for the exact 1.80 × 19mm configuration when requesting a quotation.
Coil count can vary according to collation and production configuration. KYA's broader plastic-sheet family covers multiple coil capacities, so confirm the exact count for the 1.80 × 19mm order rather than assuming a generic family quantity.
Use a coil nailer whose manufacturer specifies compatibility with the 15° plastic-sheet format, 1.80mm shank diameter, 19mm nail length and corresponding head and coil geometry. Do not rely only on the tool being described as a 15° coil nailer.
Not automatically. Plastic-sheet and wire-weld collation can use different magazine and feed geometry. Always follow the fastener specification for the exact nailer.
The 19mm dimension is the actual length of this SKU. Larger length ranges describe other products or configurations within the broader plastic-sheet coil nail family and should not replace the featured product dimension.
Provide the required quantity, nailer model, material being fastened, finish requirement, coil direction or collation requirements, packaging and destination market.
Contact KYA Fasteners regarding current sample availability. For distributor or production evaluation, test the fastener with the actual nailer, substrate and application before bulk purchasing.
Ask About 1.80x19mm Coil NailsKYA supplies plastic-sheet coil nails for fastener distributors, pneumatic-tool distributors, siding and construction suppliers, wood-product manufacturers, packaging companies and other professional buyers.
For quotations on 15° galvanized 1.80 × 19mm ring shank plastic sheet coil nails, provide the required quantity, nailer reference, finish, application, packaging and destination market.
Request a Bulk Quote View More Coil Nails
