| Finish: | |
|---|---|
| Quantity: | |
KYA 18 Gauge Brad Nails are straight-strip brads designed for trim, molding, picture frames, cabinetry, furniture and other finish woodworking applications. The featured F/25 model measures 25mm / 1 inch in length and uses a 2.00mm slight T-head with a 1.25 × 1.00mm shank.
The slender 18 gauge profile and chisel point help reduce the risk of splitting compared with heavier finish fasteners, while the small head leaves a relatively low-profile fastening mark in suitable wood and trim materials.
The nails are glue collated in straight strips of 100 pieces and packed at 5,000 nails per box. Galvanized and stainless steel options are available for different corrosion-resistance requirements.
| Specification | Details |
| Product | 18 Gauge Brad Nails |
| Model | F/25 |
| Gauge | 18 Gauge |
| Length | 25mm / 1 Inch |
| Head Width | 2.00mm Slight T-Head |
| Shank Width | 1.25mm |
| Shank Thickness | 1.00mm |
| Point Type | Chisel Point |
| Collation | Glue-Collated Straight Strip |
| Nails per Stick | 100 pcs |
| Nails per Box | 5,000 pcs |
| Boxes per Carton | 20 boxes |
| Cartons per Pallet | 50 cartons |
| Finish Options | Galvanized, Stainless Steel |
| Typical Applications | Trim, Molding, Picture Frames, Cabinetry, Furniture and Decorative Woodwork |
The featured F/25 brad nail has a nominal length of 25mm, equivalent to 1 inch. This shorter length is suitable for compatible light trim, picture-frame components, cabinet details and decorative wood parts where longer penetration is not required.
Final nail length should always be selected according to the thickness of the component, receiving material, joint design and the supported length range of the brad nailer.
The nail uses an approximately 2.00mm slight T-head. The small head helps keep the fastening point less visible than a larger finish or construction nail when driven to the correct depth.
For visible woodworking, adjust the nailer depth so the fastener is properly seated without excessive indentation or damage to the finished surface.
KYA F Series 18 gauge brad nails use a 1.25mm wide × 1.00mm thick shank. The relatively slender profile is suited to fine woodworking applications where reducing visible nail holes and limiting splitting risk are important.
Wood species, grain direction, edge distance and component thickness affect splitting risk. Test fastening in delicate, narrow or dense hardwood components before repetitive production.
The F/25 brad uses a chisel point. This point geometry supports penetration into suitable wood and helps reduce splitting risk compared with larger fasteners when correct tool settings and edge distances are used.
A chisel point does not eliminate splitting in every material. Hardness, moisture content, grain orientation and fastening position should be considered during production setup.
The nails are adhesive collated in straight strips for compatible 18 gauge brad nailers. Each KYA strip contains 100 nails.
Store collated strips in a dry location and protect them from impact or deformation. Damaged collation can affect feeding through the nailer magazine even when the individual nail dimensions are correct.
KYA lists galvanized and stainless steel options for this 18 gauge brad-nail series. The galvanized version provides corrosion protection for suitable interior and general woodworking applications.
Where higher corrosion resistance is required, a stainless steel option is available. For exterior, coastal, moisture-prone or chemically exposed applications, confirm the exact material and corrosion-resistance requirement before ordering.
KYA references Bostitch, Porter-Cable, DeWalt and Hitachi among compatible 18 gauge brad nailer brands. Compatibility depends on the individual tool model and its accepted fastener dimensions.
| Referenced Brand | What to Confirm |
|---|---|
| Bostitch | 18 gauge straight-brad magazine and support for 1-inch fasteners. |
| Porter-Cable | 18 gauge brad nailer model, straight-strip format and accepted length. |
| DeWalt | 18 gauge straight-brad specification and 25mm / 1-inch nail support. |
| Hitachi / Metabo HPT | Exact brad nailer model, gauge, magazine format and supported length. |
Porter-Cable lists its own 1-inch 18 gauge galvanized brads for several Bostitch, DeWalt, Porter-Cable, Hitachi, Paslode, Senco and Ridgid tools. However, buyers should still verify their individual nailer model before substituting fasteners.
KYA F Series brad nails are available in multiple lengths for different trim, cabinetry and woodworking requirements. All sizes shown below use the listed 18 gauge 1.25 × 1.00mm profile.
| Model | Length (mm) | Length (inch) | Pcs/Stick | Pcs/Box | Boxes/Carton | Cartons/Pallet |
|---|---|---|---|---|---|---|
| F/13 | 13 | 1/2" | 100 | 5,000 | 30 | 50 |
| F/15 | 15 | 5/8" | 100 | 5,000 | 30 | 50 |
| F/16 | 16 | 5/8" | 100 | 5,000 | 30 | 50 |
| F/19 | 19 | 3/4" | 100 | 5,000 | 20 | 50 |
| F/20 | 20 | 13/16" | 100 | 5,000 | 20 | 50 |
| F/22 | 22 | 7/8" | 100 | 5,000 | 20 | 50 |
| F/25 | 25 | 1" | 100 | 5,000 | 20 | 50 |
| F/28 | 28 | 1-1/8" | 100 | 5,000 | 20 | 50 |
| F/30 | 30 | 1-3/16" | 100 | 5,000 | 10 | 60 |
| F/32 | 32 | 1-1/4" | 100 | 5,000 | 10 | 60 |
| F/35 | 35 | 1-3/8" | 100 | 5,000 | 10 | 60 |
| F/38 | 38 | 1-1/2" | 100 | 5,000 | 10 | 60 |
| F/40 | 40 | 1-9/16" | 100 | 5,000 | 10 | 60 |
| F/44 | 44 | 1-3/4" | 100 | 5,000 | 10 | 50 |
| F/45 | 45 | 1-3/4" | 100 | 5,000 | 10 | 50 |
| F/50 | 50 | 2" | 100 | 5,000 | 10 | 50 |
| F/57 | 57 | 2-1/4" | 100 | 5,000 | 10 | 50 |
The 25mm / 1-inch F/25 size is intended for lighter finish and woodworking applications where the selected penetration depth is appropriate for the materials being joined.
Choose brad length according to the thickness of the face material, the receiving substrate and the required penetration. The 25mm / 1-inch size is shorter than many general trim brads and is therefore useful where deeper penetration is unnecessary or undesirable.
| Buyer Check | F/25 Reference |
|---|---|
| Gauge | 18 Gauge |
| Length | 25mm / 1 Inch |
| Head | 2.00mm Slight T-Head |
| Shank | 1.25 × 1.00mm |
| Point | Chisel Point |
| Collation | Straight, Glue Collated |
| Finish | Galvanized or Stainless Steel |
| Nailer | Compatible 18 gauge straight brad nailer accepting 25mm fasteners. |
18 gauge brads use a slimmer fastener profile than 15 or 16 gauge finish nails. Their smaller head and shank are useful where a less visible fastening point and reduced splitting risk are priorities.
Heavier 15 or 16 gauge finish nails generally provide more holding capability for substantial trim and woodworking components. Select the fastener according to the joint load, material thickness and desired finished appearance.
The F/25 specification is supplied at 100 nails per stick and 5,000 nails per box. The listed bulk configuration is 20 boxes per carton and 50 cartons per pallet.
| Packing Item | F/25 |
| Nails per Stick | 100 pcs |
| Nails per Box | 5,000 pcs |
| Boxes per Carton | 20 |
| Cartons per Pallet | 50 |
KYA supplies 18 gauge brad nails for cabinet manufacturers, picture-frame producers, furniture factories, trim installers, fastener distributors and professional woodworking buyers.
Custom length and finish requirements can be discussed for bulk orders. Provide the required length, finish, purchasing quantity and brad nailer model when requesting a quotation.
KYA supplies F Series 18 gauge brad nails from Changzhou, Jiangsu, China for professional finish woodworking, furniture, cabinetry and distribution applications.
Available F Series lengths include multiple sizes from short brads for light trim to longer fasteners for compatible woodworking applications, with galvanized and stainless steel options available.
The F/25 model is an 18 gauge brad nail measuring 25mm / 1 inch long, with a 2.00mm slight T-head and 1.25 × 1.00mm shank.
Typical uses include picture frames, light decorative trim, small molding profiles, cabinet details, furniture trim, paneling and other light woodworking where 25mm penetration is suitable.
The listed slight T-head width is approximately 2.00mm.
The shank measures approximately 1.25mm wide × 1.00mm thick.
Yes. KYA lists the F Series with a chisel point for controlled penetration into suitable wood materials.
Their slender profile and chisel point can reduce splitting risk compared with larger fasteners, but no nail can guarantee that wood will not split. Wood species, grain direction, edge distance and tool setup all affect the result.
Yes. They are supplied in glue-collated straight strips with 100 nails per stick.
The F/25 model is listed at 5,000 nails per box.
KYA references Bostitch among compatible brands. Confirm that the specific nailer accepts straight 18 gauge brads and supports a 25mm / 1-inch nail length.
Yes, compatible Porter-Cable 18 gauge brad nailers can use this general fastener format. Confirm the exact tool model and accepted nail dimensions before purchasing.
DeWalt is among the referenced compatible brands. Verify that the individual tool accepts straight 18 gauge brads in the 1-inch length.
KYA lists Hitachi among the referenced brands. For current Hitachi / Metabo HPT models, confirm gauge, magazine format and supported fastener length before use.
Galvanized brads provide corrosion protection, but suitability for long-term exterior, coastal or high-moisture use depends on the coating specification and service environment. Consider the available stainless steel option where higher corrosion resistance is required.
Yes. KYA lists a stainless steel finish option for the 18 gauge brad nail series.
The listed range includes F/13, F/15, F/16, F/19, F/20, F/22, F/25, F/28, F/30, F/32, F/35, F/38, F/40, F/44, F/45, F/50 and F/57.
18 gauge brads are thinner and generally leave a smaller fastening mark, making them useful for lighter trim and decorative work. Heavier 15 or 16 gauge finish nails are typically selected for applications requiring greater holding capability.
KYA lists custom length and finish options for bulk-order requirements. Provide the required specification, quantity and nailer model when requesting a quotation.
