The 7116 pneumatic upholstery stapler is designed for professional furniture upholstery, automotive trim, picture frames, light trim work and other fine wire fastening applications. It drives 22 Gauge 71 Series / Senco C-type staples from 6 mm to 16 mm and operates at 60–100 PSI.
With a listed tool weight of approximately 0.93 kg / 2.05 lbs, dimensions of 150 × 43 × 213 mm and a magazine capacity of 180 staples, the 7116 combines a compact tool body with the staple capacity required for repetitive upholstery and production work.
The KYA 7116 is a compact pneumatic fine wire stapler for 71 Series fasteners. The narrow 22 Gauge staple profile is suitable for applications where fabric, vinyl, trim or other relatively thin materials need to be fastened without using a heavier construction staple.
22 Gauge 71 Series: Uses common fine wire upholstery staples.
6–16 mm staple range: Supports multiple material thicknesses and fastening requirements.
180-staple magazine: Reduces reload frequency during repetitive production work.
0.93 kg tool weight: Compact format for upholstery benches and assembly stations.
60–100 PSI: Operates with a regulated compressed-air supply within the specified range.
Rubber grip: Provides a stable gripping surface during repetitive use.
Magazine loading: Designed for collated 71 Series fine wire staples.
| Parameter | Specification |
|---|---|
| Model | 7116 |
| Product Code | KYA-7116 |
| Tool Type | Pneumatic Fine Wire Upholstery Stapler |
| Staple Gauge | 22 Gauge |
| Staple Series | 71 Series / Senco C-Type |
| Nominal Crown | 3/8" / Approx. 9.0 mm |
| Staple Length Range | 1/4"–5/8" / 6–16 mm |
| Magazine Capacity | 180 Staples |
| Operating Pressure | 60–100 PSI / 4–7 bar |
| Tool Weight | Approx. 0.93 kg / 2.05 lbs |
| Dimensions | 150 × 43 × 213 mm |
The 7116 is designed for 22 Gauge 71 Series fine wire staples from 6 mm to 16 mm. Several fastener manufacturers use different series names for corresponding fine wire staple formats.
| Staple Reference | Compatibility Note |
|---|---|
| 71 Series | Primary fine wire staple format for the KYA 7116. |
| BeA 71 | Common cross-reference for the 71 Series format. |
| SENCO C | Common corresponding fine wire staple family. |
| OMER 3G | OMER identifies the 3G format as equivalent to BeA 71 and SENCO C. |
| PREBENA V | Common corresponding fine wire staple reference. |
| KIHLBERG 670 | Commonly cross-referenced with this fine wire staple family. |
When replacing another staple brand, confirm the complete fastener dimensions and leg length. The KYA 7116 is specified for 6–16 mm staples; the minimum fastener length of another manufacturer's stapler should not be assumed to apply to this tool.
| Feature | Function |
|---|---|
| Compact 0.93 kg Body | Suitable for repetitive upholstery and bench assembly work. |
| 180-Staple Magazine | Reduces the frequency of staple reloads during production. |
| Rubber Grip | Provides a stable contact surface for tool handling. |
| 6–16 mm Fastener Range | Allows different staple lengths to be matched to different material thicknesses. |
| 60–100 PSI Working Range | Supports regulated pneumatic operation within the specified pressure range. |
| Fine Wire Fastening | Suitable where a smaller staple profile is preferred for fabric, vinyl and trim. |
The 7116 is intended for professional fine wire fastening where the material, substrate and selected 71 Series staple length are suitable for pneumatic stapling.
| Application | Typical Fastening Work |
|---|---|
| Furniture Upholstery | Attaching fabric, backing and upholstery material to suitable frames. |
| Automotive Upholstery | Fastening compatible vinyl, fabric and interior trim. |
| Picture Frames | Fastening backing and suitable lightweight frame components. |
| Mattress and Bedding | Fine wire fastening of suitable fabric and light bedding components. |
| Cabinet and Trim Work | Attaching compatible fabric, light trim and finishing materials. |
| House Wrap | Fastening suitable building wrap where this staple system is appropriate. |
| Insulation | Fastening compatible insulation facing and lightweight materials. |
| Shoe and Craft Assembly | Light fastening work on compatible materials and substrates. |
The 7116 accepts staple lengths from 6 mm to 16 mm. The correct size depends on the thickness of the material being attached, the substrate and the penetration required for secure fastening.
| Selection Factor | What to Check |
|---|---|
| Top Material | Confirm the thickness of fabric, vinyl, felt or trim. |
| Substrate | Identify the wood, board or other compatible base material. |
| Required Penetration | Use sufficient staple length without unnecessary over-penetration. |
| Staple Series | Use compatible 22 Gauge 71 Series / Senco C-type staples. |
| Tool Range | Keep staple length within the listed 6–16 mm range. |
Use clean and regulated compressed air within the specified 60–100 PSI / 4–7 bar range.
Do not exceed the maximum listed operating pressure.
Use only compatible 22 Gauge 71 Series staples within the 6–16 mm range.
Test staple penetration on the actual material before continuous production.
Inspect the driver, nose and magazine when staple feeding becomes irregular.
Disconnect the compressed-air supply before clearing jams or servicing internal components.
Follow the applicable lubrication and maintenance instructions for the supplied tool configuration.
| Symptom | Possible Cause | Recommended Check |
|---|---|---|
| Air leak at cylinder cap while idle | Loose head valve seal or O-ring | Inspect the head valve piston set and replace damaged sealing components. |
| Air leak at cylinder cap while idle | Worn O-ring or gasket under cap | Inspect and replace the worn O-ring or gasket. |
| Air leak at trigger while idle | Damaged trigger O-ring | Replace the trigger O-ring. |
| Air leak at trigger while idle | Damaged stem O-ring | Replace the stem O-ring. |
| Air leak at trigger while idle | Dirt in trigger valve | Clean the trigger valve and inspect the sealing surfaces. |
| Air leak at cylinder cap while firing | Damaged piston O-rings | Inspect and replace worn piston O-rings. |
| Air leak at cylinder cap while firing | Damaged seal under cap | Inspect and replace the damaged seal. |
| Air leak at nose while firing | Worn bumper | Inspect and replace the bumper. |
| Air leak at nose while firing | Loose or damaged driver assembly | Inspect the driver assembly and replace damaged parts if required. |
| Air leak at trigger while firing | Worn trigger valve head | Replace the trigger valve head. |
| Driver does not return fully | Bent driver or misaligned nose | Inspect the driver and nose-to-magazine alignment. |
| Driver does not return fully | Worn nozzle | Inspect and replace the nozzle if necessary. |
| Driver does not return fully | Tight piston O-ring or cylinder condition | Check lubrication and inspect the piston O-ring and cylinder. |
Always disconnect the compressed-air supply before disassembling the tool, clearing a jam or servicing internal components.
KYA Fasteners supplies the 7116 pneumatic stapler for furniture manufacturers, upholstery workshops, automotive trim operations, fastening-tool distributors and other professional users requiring a compact 22 Gauge 71 Series stapler.
When requesting a quotation, provide the required quantity, destination country and staple lengths you plan to use. If the 7116 is replacing an existing upholstery stapler, provide the current tool model and staple reference for compatibility comparison.
The 7116 uses 22 Gauge 71 Series / Senco C-type fine wire staples.
The KYA 7116 is listed for staple lengths from 6 mm to 16 mm / 1/4 inch to 5/8 inch.
The current KYA specification lists 6 mm as the minimum staple length. Some other 71 Series staplers accept shorter fasteners, but those specifications should not automatically be applied to the KYA 7116.
The 7116 uses the 71 Series fine wire format, commonly described as approximately 3/8 inch / 9 mm crown.
The listed operating pressure is 60–100 PSI / approximately 4–7 bar.
The listed magazine capacity is approximately 180 staples.
The listed tool weight is approximately 0.93 kg / 2.05 lbs.
BeA 71 is a common corresponding staple reference for this fine wire format. Confirm that the selected fastener also falls within the KYA 7116's 6–16 mm length range.
SENCO C is commonly cross-referenced with the 71 Series format. Verify the exact staple dimensions and leg length before bulk ordering.
OMER identifies the 3G staple format as equivalent to BeA 71 and SENCO C. The operating specifications of an OMER stapler are separate from the specifications of the KYA 7116.
Yes. Furniture upholstery is one of the primary applications for this 22 Gauge pneumatic fine wire stapler.
It can be used for compatible automotive vinyl, fabric and interior trim where the 71 Series staple format and selected staple length are suitable for the material and substrate.
It can be used for compatible house wrap and insulation-facing applications where a 71 Series fine wire staple is suitable for the installation method and substrate.
Provide the required tool quantity, destination country and staple lengths you intend to use. For replacement applications, also provide the existing stapler model and staple series.
KYA Fasteners has produced the 7116 pneumatic stapler since 2003 and exports to more than 50 countries. The minimum order quantity is 1 unit. OEM custom branding is available. The listed lead time is 15–25 days. Shipping to the USA, EU, Australia and Canada is listed at 15–25 days; confirm destination-specific delivery timing when requesting a quotation.
