| Finish: | |
|---|---|
| Quantity: | |
KYA F15 18 gauge galvanized brad nails are 15 mm straight-strip finish nails designed for compatible 18GA brad nailers. Their compact approximately 1.25 × 1.00 mm wire profile and 2.00 mm head width make them suitable for trim, molding, cabinetry, furniture and other finish woodworking applications where a small fastening mark is preferred.
F15 is approximately 15 mm / nominal 5/8 inch long. This short length is commonly used for thinner trim, cabinet components, decorative molding, picture frames, paneling and similar applications where a longer brad is unnecessary.
The standard product uses an electro-galvanized finish for general indoor and protected-environment applications. Stainless-steel alternatives are available within the KYA brad-nail range for applications requiring greater corrosion resistance; confirm the required material and size when ordering.
18 Gauge: approximately 1.25 mm wide × 1.00 mm thick for fine finish fastening.
15 mm / nominal 5/8" length: short brad size for thinner trim and woodworking components.
2.00 mm head width: compact head profile designed to leave a relatively small visible fastening point.
Chisel point: suitable for controlled penetration into compatible wood, MDF and trim materials.
Straight strip collation: for compatible 18GA straight-magazine brad nailers.
Electro-galvanized finish: provides basic corrosion protection for general indoor and protected applications.
100 nails per stick: matches the magazine capacity of many professional 18GA brad nailers.
5,000 nails per box: suitable for distributors, woodworking shops and production users.
| Parameter | Specification |
|---|---|
| Model | F15 |
| Fastener Type | Straight Collated Brad Nail |
| Gauge | 18 Gauge |
| Length | 15 mm / nominal 5/8" |
| Head Width | Approximately 2.00 mm |
| Wire Width | Approximately 1.25 mm |
| Wire Thickness | Approximately 1.00 mm |
| Point | Chisel Point |
| Collation | Straight Strip |
| Standard Finish | Electro-Galvanized |
| Nails per Stick | 100 pcs |
| Nails per Box | 5,000 pcs |
| Boxes per Carton | 30 boxes |
| Cartons per Pallet | 50 cartons |
| Gross Weight per Carton | Approximately 20.05 kg |
A short 5/8-inch-class brad is useful when the workpiece does not require the penetration of a 1-inch, 1-1/2-inch or 2-inch finish nail. It can reduce the risk of excessive penetration through thin trim, molding, cabinet components and decorative work.
The 18GA profile is smaller than common 15GA and 16GA finish nails. This makes it suitable where appearance matters, although the smaller fastener also provides less fastening capacity than a heavier finish nail.
Decorative molding and light trim
Cabinet assembly and cabinet trim
Face frames and light woodworking components
Picture and mirror frames
Door and window trim
Paneling and wainscoting
Furniture assembly and repair
Thin plywood and MDF components
Decorative woodworking and production trim
The standard F15 uses an electro-galvanized surface. This zinc coating provides basic corrosion protection compared with untreated carbon steel and is commonly used for indoor finish carpentry, cabinetry, furniture and other protected applications.
Electro-galvanized brads should not be treated as equivalent to stainless steel or heavier corrosion-resistant coatings for continuously wet, salt-air, highly corrosive or preservative-treated exterior environments.
| Fastener | Typical Use | Selection Consideration |
|---|---|---|
| Electro-Galvanized 18GA Brad | Indoor trim, molding, cabinetry, furniture and protected woodworking. | Economical general-purpose finish where severe corrosion exposure is not expected. |
| 304 Stainless Steel Brad | Moist or exterior applications, cedar, redwood and compatible treated-wood trim. | Greater corrosion resistance than electro-galvanized carbon steel. |
| 316 Stainless Steel Brad | Applications requiring higher resistance to salt air or chloride-rich environments. | Confirm exact size and availability for the required application. |
F15 belongs to the common 5/8-inch 18GA straight brad size class. Many professional 18GA nailers accept 5/8-inch brads, but tool compatibility should be checked by exact nailer model, fastener profile, magazine and head design.
| Tool / Fastener Platform | Published Specification | F15 Selection Guidance |
|---|---|---|
| BOSTITCH BTFP12233 / BT1855 | 18GA BT13XX brads, approximately 5/8"–2-1/8"; BT1300 is the 5/8" size. | F15 falls within the published length class; compare the complete brad profile before cross-brand use. |
| DEWALT DCN680 / DWFP12233 | 18GA brads, approximately 5/8"–2-1/8". | F15 is at the published minimum length; confirm straight-strip profile and head geometry. |
| Metabo HPT NT1850DG / NT1850DFT | 18GA straight brads, approximately 5/8"–2". | F15 is within the published length range; confirm the exact tool model before production use. |
| SENCO F-18XP | 18GA AX / AY style brads, approximately 5/8"–2-1/8". | SENCO AX10EAA is a 5/8" galvanized straight-strip 18GA brad; compare head and strip profile before substitution. |
| Bosch 18GA Brad Nailer Platform | Bosch lists a 5/8" galvanized 18GA brad within its compatible fastener range. | Same nominal length and gauge class; confirm exact fastener geometry before cross-brand use. |
Several established fastener systems use a 5/8-inch galvanized 18GA straight brad. These references can help distributors and professional users identify the required size class, but they should not be treated as automatic guarantees of interchangeability.
| Reference | Nominal Size | Description |
|---|---|---|
| KYA F15 | 15 mm / nominal 5/8" | 18GA electro-galvanized straight brad |
| BOSTITCH BT1300 | 5/8" / 15 mm | 18GA BT13XX-series brad |
| SENCO AX10EAA | 5/8" | 18GA galvanized, chisel point, straight-strip brad |
| Bosch GNH18G062GV | 5/8" | 18GA galvanized brad |
For a replacement order, compare the gauge, actual wire dimensions, head profile, strip geometry and tool specification before volume use.
| Item | Length | Pcs / Stick | Pcs / Box | Boxes / Carton | Cartons / Pallet | G.W. / Carton |
|---|---|---|---|---|---|---|
| F15 | 15 mm / nominal 5/8" | 100 | 5,000 | 30 | 50 | 20.05 kg |
| F13 | 13 mm / 1/2" | 100 | 5,000 | 30 | 50 | 17.65 kg |
| F16 | 16 mm / nominal 5/8" | 100 | 5,000 | 30 | 50 | 21.37 kg |
| F19 | 19 mm / 3/4" | 100 | 5,000 | 20 | 50 | 17.7 kg |
| F50 | 50 mm / 2" | 100 | 5,000 | 10 | 50 | 21.8 kg |
One inch equals 25.4 mm, so an exact 5/8 inch measurement is approximately 15.875 mm. For this reason, different fastener catalogs may describe either a 15 mm or 16 mm brad as a nominal 5/8-inch product.
When the exact metric length matters, order by the specific model and millimeter dimension rather than relying only on the nominal inch description. KYA F15 is the 15 mm model, while F16 is the 16 mm model.
| Fastener | General Characteristic | Typical Application |
|---|---|---|
| 18GA Brad Nail | Smaller wire and compact head. | Light trim, molding, cabinetry, furniture and decorative woodworking. |
| 16GA Finish Nail | Larger cross section and greater fastening capacity. | Heavier trim, casing and finish carpentry. |
| 15GA Finish Nail | Heavier finish fastener, often used in angled nailer systems. | Thicker trim and more demanding finish connections. |
F15 can be useful for suitable MDF, thin plywood and composite-wood components because its short length reduces unnecessary penetration. Actual holding strength depends on substrate density, material thickness, edge distance and the direction of the fastener.
For production furniture or cabinetry, test the fastener on the actual board and joint before volume use, particularly when fastening close to panel edges.
Choose the brad length according to the trim thickness and required penetration into the substrate. F15 is primarily a short finish fastener. Thicker casing, baseboard or molding assemblies may require a longer 18GA brad or a heavier finish-nail platform.
The correct drive depth should leave the brad properly seated without excessive countersinking or surface damage.
| Order Information | What to Provide |
|---|---|
| Fastener Model | F15 / 15 mm / nominal 5/8". |
| Gauge | 18GA. |
| Nailer Brand and Model | Provide the exact tool model for compatibility checking. |
| Finish | Specify electro-galvanized or required stainless-steel alternative. |
| Application | Specify trim, cabinet, furniture, MDF, plywood, molding or other use. |
| Quantity | Provide required boxes, cartons, pallets or annual consumption. |
Discuss Your F15 Brad Nail Requirement
KYA F15 is an 18 gauge brad nail approximately 15 mm long, commonly described as a nominal 5/8-inch brad.
The published profile is approximately 1.25 mm wide × 1.00 mm thick, with an approximately 2.00 mm head width.
The current packing specification lists 100 nails per stick.
The current packing specification lists 5,000 nails per box.
For F15, the current product table lists 30 boxes per carton.
The published gross weight is approximately 20.05 kg per carton. Confirm current packing before shipment because packaging configuration can change.
The standard F15 configuration shown on this page uses an electro-galvanized finish.
Yes. Electro-galvanized brads are commonly used for indoor and protected trim, molding, cabinetry and furniture applications where severe corrosion exposure is not expected.
The standard electro-galvanized F15 is better suited to indoor or protected applications. For demanding exterior, salt-air or high-corrosion environments, specify a suitable stainless-steel fastener where the application permits an 18GA brad.
KYA also offers stainless-steel 18GA brad nails. Confirm the required stainless grade, exact length and current availability when requesting a quotation.
The DEWALT DCN680 is specified for 18GA brads from approximately 5/8" to 2-1/8", so F15 falls within its published length range. Confirm the complete strip and head profile before cross-brand use.
The DWFP12233 is specified for 18GA brads from approximately 5/8" to 2-1/8". F15 therefore falls within its published length range, subject to fastener-profile compatibility.
Several current Metabo HPT 18GA brad nailers accept straight brads from approximately 5/8" to 2", placing F15 within their published length range. Check the exact tool model before use.
SENCO specifies the F-18XP for 18GA AX and AY style brads from approximately 5/8" to 2-1/8". F15 is in the same nominal length class, but head and strip geometry should be confirmed before substitution.
Both are nominal 5/8-inch 18GA galvanized straight-strip brads. Use the complete fastener dimensions and nailer specification to confirm interchangeability.
Yes, both belong to the nominal 5/8-inch 18GA brad size class. Cross-brand use should still be confirmed from the nailer and fastener specifications.
An exact 5/8 inch equals approximately 15.875 mm. Depending on the manufacturer's metric convention, nominal 5/8-inch brads may therefore be listed as either 15 mm or 16 mm. Order by the exact model and metric length when the difference matters.
No. Their small cross section can reduce splitting compared with heavier fasteners, but wood species, moisture content, edge distance, grain direction and nail placement all affect the result.
No fastener can guarantee jam-free operation in every tool and operating condition. Correct fastener profile, magazine condition, loading, air pressure or battery condition, driver condition and tool maintenance all affect feeding.
F15 is a small finish brad intended for suitable trim and woodworking applications. It should not replace structural nails, screws or approved connectors where structural fastening is required.
Yes. Check magazine feeding, drive depth, head position, surface appearance and holding performance in the actual nailer and workpiece before full-volume production.
Provide the required model or length, nailer brand and model, finish or material, application, quantity and destination market.
KYA supplies F15 15 mm / nominal 5/8-inch 18 gauge galvanized brad nails for fastener distributors, cabinet manufacturers, furniture factories, woodworking suppliers and professional finish users. Send your nailer model, required quantity, application and finish requirement to confirm the appropriate configuration.
The listed minimum order quantity is 50 cartons (one pallet), with a stated lead time of 15–20 days. A free 1,000-piece sample pack is available; the buyer covers freight. Confirm current production timing and sample arrangements when requesting a quotation.
